2.9L & 3.0L V6 Tech General discussion of 2.9L and 3.0L V6 Ford Ranger engines.

04 With oil leak!

  #1  
Old 05-27-2007
mj550's Avatar
Member
Thread Starter
Join Date: Apr 2006
Location: USA
Posts: 601
Likes: 0
Received 0 Likes on 0 Posts
04 With oil leak!

I have a new problem on my hands now! I have an oil leak! I seen a small drop on the floor, and I got under the truck and sure enough it looks like a slow leak possibly coming from the rear main, cant tell for sure though. You can see the front of the pan is damp and it leads up between the trans and engine. I am NOT happy! A truck this new should NOT be leaking ANY oil! I don't know what to do, I really cant take it apart to fix it right now... Warrenty is over. Any suggestions?
 
  #2  
Old 05-28-2007
Grizzlybear34's Avatar
Member
Join Date: May 2006
Location: Bradenton, Florida
Posts: 198
Likes: 0
Received 0 Likes on 0 Posts
Mike - When did you get your oil changed last? Is it possible it could be something as simple as your filter leaking? I had that problem once with my wife's truck, freaked out a little only to find the filter wasn't tight enough.

Good luck.
 
  #3  
Old 05-28-2007
edge05runner's Avatar
Member
Join Date: Apr 2005
Location: Peoria az
Posts: 142
Likes: 0
Received 0 Likes on 0 Posts
yeah check your filter because i took mine to ford and i thought the same thing and sure enough they just didnt tighten the filter all the way
 
  #4  
Old 05-28-2007
mj550's Avatar
Member
Thread Starter
Join Date: Apr 2006
Location: USA
Posts: 601
Likes: 0
Received 0 Likes on 0 Posts
Filter is nice and tight, my dad blames it on me using full synthetic oil saying its leaking thorugh the seals blah blah, I don't think that's it but you never know. Actaully now that I think black, when I bought the truck I was using motorcraft 5w20 synblend, and the previous owner was using synblend oil to, but a different brand. When I started using my fullsyn mobil 1 the oil seemd low when I changed it, and I thought the engine could of been consuming it. I guess it was this leak the whole time. Im just not sure what I should do at this point. Could it really be the mobil 1 easing its way past the seals?
 
  #5  
Old 05-28-2007
Werty's Avatar
Member
Join Date: Oct 2004
Location: Tucson
Posts: 525
Likes: 0
Received 0 Likes on 0 Posts
did you do the oil and filter change yourself? Take off the filter and make sure you only have 1 seal on there. Sometimes an old seal can get stuck and when you have two on it leaks inbetween the two

or possibly your screw at the bottom of your oil pan is loose. Jiffylube always does that with mine and I have to tighten it at home


in most cases an oil leak is an easy fix
 
  #6  
Old 05-28-2007
mj550's Avatar
Member
Thread Starter
Join Date: Apr 2006
Location: USA
Posts: 601
Likes: 0
Received 0 Likes on 0 Posts
Originally Posted by Werty
did you do the oil and filter change yourself? Take off the filter and make sure you only have 1 seal on there. Sometimes an old seal can get stuck and when you have two on it leaks inbetween the two

or possibly your screw at the bottom of your oil pan is loose. Jiffylube always does that with mine and I have to tighten it at home


in most cases an oil leak is an easy fix
Yeah I do it myself, its only got one seal on the filter, because I always wipe off the block before I put the new one on. Plug is tight. You can tell its coming from above. Ive talked to several people today, and did some reasearching and found others have had problems with mobil1 causing seal leaks in some vehicles, and people have switched it out for something else and the leaks would stop after a bit. I may try that... Good looking truck btw..
 
  #7  
Old 05-28-2007
Werty's Avatar
Member
Join Date: Oct 2004
Location: Tucson
Posts: 525
Likes: 0
Received 0 Likes on 0 Posts
Originally Posted by mj550
Yeah I do it myself, its only got one seal on the filter, because I always wipe off the block before I put the new one on. Plug is tight. You can tell its coming from above. Ive talked to several people today, and did some reasearching and found others have had problems with mobil1 causing seal leaks in some vehicles, and people have switched it out for something else and the leaks would stop after a bit. I may try that... Good looking truck btw..
thats interesting, I've never heard of certain oil brands leaking...but I suppose its possible

and thanks for the compliment
 
  #8  
Old 05-28-2007
mj550's Avatar
Member
Thread Starter
Join Date: Apr 2006
Location: USA
Posts: 601
Likes: 0
Received 0 Likes on 0 Posts
No problem. I took the mobil1 out and went about bought a new filter and 5 quarts of motorcraft 5w20 synblend, what it calls for from the factory. It wasnt leaking when I had that in there before, so we'll see what happens this time. My grandpa was telling me that my grandma had a brand new s10 years ago, and put synthetic mobil 1 in, and it started leaking after the first couple changes. He took it back out and put castrol back in, and the leak went away. Intresting...
 
  #9  
Old 05-29-2007
Grizzlybear34's Avatar
Member
Join Date: May 2006
Location: Bradenton, Florida
Posts: 198
Likes: 0
Received 0 Likes on 0 Posts
Let us know if that stops it. I haven't heard of that before.
 
  #10  
Old 06-21-2007
mj550's Avatar
Member
Thread Starter
Join Date: Apr 2006
Location: USA
Posts: 601
Likes: 0
Received 0 Likes on 0 Posts
Well guys, its been about 3k miles and it's still dry underneith and just a tad above full, same spot it was when I changed it. Im really happy. I used to see a drip everyday even after cleaning it off underneith, havent seen one since the oil change. Im sticking with what it says to use.
 
  #11  
Old 06-21-2007
bryanjints's Avatar
Member
iTrader: (1)
Join Date: Dec 2005
Location: Mount Holly, NJ
Posts: 1,857
Likes: 0
Received 1 Like on 1 Post
That right there amazes me. I am dumbfounded by this. Someone needs to explain why a certain oil would cause a leak.
 
  #12  
Old 06-21-2007
Mike9825's Avatar
Member
Join Date: Jun 2006
Location: Willard OH
Posts: 489
Likes: 0
Received 1 Like on 1 Post
Originally Posted by bryanjints
That right there amazes me. I am dumbfounded by this. Someone needs to explain why a certain oil would cause a leak.
x2!

I've been using Mobil1 5w30 and MC filter for 50K miles and 4 years, changing every 7K miles average. My truck is bone dry, it don't leak oil and it never has. I too would be interested in knowing more about this. -Mike-
 
  #13  
Old 06-21-2007
mj550's Avatar
Member
Thread Starter
Join Date: Apr 2006
Location: USA
Posts: 601
Likes: 0
Received 0 Likes on 0 Posts
I bought the truck in may of 06. Never had a problem with oil consumption until after i started using the full synthetic mobil 1 on like the third oil change I did on the truck. I did everything the same when I changed the oil this past time except for the motorcraft 5w20 I have in there now, which is what I used when I first bought the truck. Ive always had the filter and plug tight. Like I said, the leak was coming from far up like between the engine and transmission. I havent seen anything, and its right up on full where it should be about 3k later. Normally it would of used/leaked some by now.
 
  #14  
Old 06-21-2007
Mike9825's Avatar
Member
Join Date: Jun 2006
Location: Willard OH
Posts: 489
Likes: 0
Received 1 Like on 1 Post
a vehicle that's been using regular oil for sometime and then switching over to synthetic will cause it to consume some oil, that's normal until the engines internals are cleaned out. Ring packs, heads, main bearings etc...

Why the leak happened in your case, I don't know the full story. Why switching to a synthetic would cause it. -Mike-
 
  #15  
Old 06-21-2007
mj550's Avatar
Member
Thread Starter
Join Date: Apr 2006
Location: USA
Posts: 601
Likes: 0
Received 0 Likes on 0 Posts
Originally Posted by Mike9825
a vehicle that's been using regular oil for sometime and then switching over to synthetic will cause it to consume some oil, that's normal until the engines internals are cleaned out. Ring packs, heads, main bearings etc...

Why the leak happened in your case, I don't know the full story. Why switching to a synthetic would cause it. -Mike-
Yes but I started using it at like around 23k, I have changed back at 41k and all is well so far. Also, I had a leak, the engine itself wasnt consuming it.

Edit: nevermind, I seen what you said at the end.
 
  #16  
Old 06-21-2007
The_Edge's Avatar
Member
Join Date: Jun 2007
Location: Spanaway
Posts: 9
Likes: 0
Received 0 Likes on 0 Posts
oil

what ever the factory recomends for it, thats always the best bet on anything. Kind of why they put it in the manual.. lol

Glad you got it stopped. If i could get my mustang to stop like that, i too would be happy (rear main is bad)
 
  #17  
Old 06-22-2007
nated0g's Avatar
Member
Join Date: Nov 2005
Location: Millington, TN
Posts: 467
Likes: 0
Received 0 Likes on 0 Posts
that is what i run is the full synthetic mobil one. i am starting to see oil consumption. maybe i will switch to another brand like castrol.
the only reason i went to mobil one is that you can run it for 15k. i run 2000 miles a month. was just trying to save money.
 
  #18  
Old 06-22-2007
Mike9825's Avatar
Member
Join Date: Jun 2006
Location: Willard OH
Posts: 489
Likes: 0
Received 1 Like on 1 Post
I do about 1400 miles a month for work, so in my case synthetic makes sense. I don't see any other advantages of it other than longer drain intervals. Regular oil will do just as good in all respects in a daily driver under normal conditions with 4-5000 mile changes.

I'm sure M1 could hold up for 15K but I just don't have the ***** for it. -Mike-
 
  #19  
Old 06-22-2007
mj550's Avatar
Member
Thread Starter
Join Date: Apr 2006
Location: USA
Posts: 601
Likes: 0
Received 0 Likes on 0 Posts
I'll do mine between 3k-5k. The oil still looks really good right now after about 3k, so I may just go on to 5k.
 
  #20  
Old 10-23-2007
rangeredge_03's Avatar
Member
Join Date: Oct 2007
Location: lubbock,tx
Posts: 594
Likes: 0
Received 1 Like on 1 Post
i really don't like m1 it seems to be thinner to me the oil that i really like is castrol syntech it seems to hold up better then m1. i have seen i alot of oil since that is my job as a lube tech an all of the castrol product don't seem to break down like other oils an for motorcaft oil who even makes it ?
 
  #21  
Old 10-23-2007
mj550's Avatar
Member
Thread Starter
Join Date: Apr 2006
Location: USA
Posts: 601
Likes: 0
Received 0 Likes on 0 Posts
Originally Posted by rangeredge_03
i really don't like m1 it seems to be thinner to me the oil that i really like is castrol syntech it seems to hold up better then m1. i have seen i alot of oil since that is my job as a lube tech an all of the castrol product don't seem to break down like other oils an for motorcaft oil who even makes it ?
Hey, I have thought about trying syntec. Do you have any experience with valvolines synpower?

Thanks
Mike
 
  #22  
Old 10-23-2007
rangeredge_03's Avatar
Member
Join Date: Oct 2007
Location: lubbock,tx
Posts: 594
Likes: 0
Received 1 Like on 1 Post
no i have never tried or heard anything about it valvoline is an ok oil i still thank that syntec is the best way to go. my next oil change will be castrol syntech 5w20
 
  #23  
Old 10-24-2007
dead's Avatar
Member
Join Date: Sep 2007
Location: Rockwall/Dallas, TX
Posts: 382
Likes: 0
Received 0 Likes on 0 Posts
I have the same little oil leak and I use mobile1 full sythn. In fact I've had it for quite some time. Maybe on my next change I'll switch and see if the leak stops.

Oh, and I have used mobil1 full synth since after my second oil change in the truck. (i have owned it since new)

edit: mj550, I see youre in Cinci. I bought my truck in Dayton (miamisburg) when I lived in Ohio :)
 
  #24  
Old 10-24-2007
mj550's Avatar
Member
Thread Starter
Join Date: Apr 2006
Location: USA
Posts: 601
Likes: 0
Received 0 Likes on 0 Posts
Originally Posted by dead
I have the same little oil leak and I use mobile1 full sythn. In fact I've had it for quite some time. Maybe on my next change I'll switch and see if the leak stops.

Oh, and I have used mobil1 full synth since after my second oil change in the truck. (i have owned it since new)

edit: mj550, I see youre in Cinci. I bought my truck in Dayton (miamisburg) when I lived in Ohio :)
If you do try it, let us know what kind of oil you use to replace it. If you want to stay synthetic then just pick a different brand. Id say definatly try it though, or heck throw in some motorcraft 5w20 synthetic blend that is used from the factory and see if it stops. If it works, then that will definatly suggest something. Keep us posted.
 
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
yaro1996
Oil & Lubrication
4
07-07-2017 02:29 PM
iplayloudly
2.9L & 3.0L V6 Tech
2
12-12-2011 04:04 PM
DillonT
2.9L & 3.0L V6 Tech
17
09-16-2011 07:01 PM
Fenech627
2.9L & 3.0L V6 Tech
5
10-04-2010 05:22 PM
SonicRanger001
Drivetrain Tech
6
12-22-2005 01:04 PM


Thread Tools
Search this Thread
Quick Reply: 04 With oil leak!



All times are GMT -6. The time now is 06:22 PM.