4.0L OHV & SOHC V6 Tech General discussion of 4.0L OHV and SOHC V6 Ford Ranger engines.

03 4.0 idle problem

Thread Tools
 
Search this Thread
 
  #1  
Old 09-09-2011
03nw4.0's Avatar
Member
Thread Starter
Join Date: Sep 2011
Location: ARLINGTON
Posts: 1
Likes: 0
Received 0 Likes on 0 Posts
03 4.0 idle problem

hey i guys i got a 03 4.0 4x4 manual. its got 80k. and it starts fine then after a couple mins it

starts to shake and idles at like 300 then will start to shake pretty good. it runs fine on

freeway but as soon as i hit stop lights it sputters and wants to die on me. sometimes it will

run half power then kick in outta no where. k@n is fine and i ran a bottle of injecter cleaner

thru it and still does it. if ya guys know id much appreciate it.
 
  #2  
Old 09-14-2011
klc317's Avatar
Member
Join Date: Sep 2006
Location: Cincinnati, OH
Posts: 953
Likes: 0
Received 6 Likes on 4 Posts
Is it showing a check engine light? Any codes?
 
  #3  
Old 09-14-2011
OTRtech's Avatar
Member
Join Date: Mar 2007
Location: Upstate,NY
Posts: 2,598
Likes: 0
Received 11 Likes on 11 Posts
Did you re-oil the K@N just before it started doing this?
 
  #4  
Old 09-22-2011
TheRealBoggs's Avatar
Member
Join Date: Jan 2011
Location: Springfield, VA
Posts: 62
Likes: 0
Received 1 Like on 1 Post
I had the exact same thing happen. It was my idle air control valve. It caused some suction problems that worked a couple hoses loose. Took $50 and an hour and a half to fix.
 
  #5  
Old 09-22-2011
98_ranger's Avatar
Member
Join Date: Sep 2011
Location: Columbia,SC
Posts: 180
Likes: 0
Received 0 Likes on 0 Posts
i have sorta the same problem, but i have a 1998 ranger longbed 2wd, and mine will shake extremly bad, and wont stay on. it will idle for a good 5 seconds. then it cuts off. i have changed the sparkplugs, the fuel pump, the idle postioner sensor. and the fuel sensor. it will not throw codes.
not im at the point where i just want to dig a hole and push it in it.
some please help!!
 
  #6  
Old 09-22-2011
TheRealBoggs's Avatar
Member
Join Date: Jan 2011
Location: Springfield, VA
Posts: 62
Likes: 0
Received 1 Like on 1 Post
Maybe you have a PCV tube come loose?
 
  #7  
Old 09-22-2011
98_ranger's Avatar
Member
Join Date: Sep 2011
Location: Columbia,SC
Posts: 180
Likes: 0
Received 0 Likes on 0 Posts
ill check that when i get home, any more suggestions?
 
  #8  
Old 09-22-2011
TheRealBoggs's Avatar
Member
Join Date: Jan 2011
Location: Springfield, VA
Posts: 62
Likes: 0
Received 1 Like on 1 Post
Without getting a fault code, I'm not sure. It sounds like an airflow issue, though.
 
  #9  
Old 09-22-2011
98_ranger's Avatar
Member
Join Date: Sep 2011
Location: Columbia,SC
Posts: 180
Likes: 0
Received 0 Likes on 0 Posts
im getting fuel pressure but idk what is going on!!
 
  #10  
Old 09-23-2011
98_ranger's Avatar
Member
Join Date: Sep 2011
Location: Columbia,SC
Posts: 180
Likes: 0
Received 0 Likes on 0 Posts
i clean the PCV tube. and it still wont run
 
  #11  
Old 10-06-2011
StxDangerRanger's Avatar
RF Veteran
iTrader: (2)
Join Date: Dec 2010
Location: Michigan
Posts: 6,315
Likes: 0
Received 6 Likes on 6 Posts
Originally Posted by 98_ranger
i clean the PCV tube. and it still wont run
when you took your PCV off, did you hear something rattling around in it?
Also, What about your EGR? When you start it up, do you have the pedal to the floor to try and keep it running?
 
  #12  
Old 10-06-2011
Y2KTJ's Avatar
Member
Join Date: Aug 2009
Location: Okeechobee,FL / Singapore
Posts: 563
Likes: 0
Received 0 Likes on 0 Posts
thats what mine would do until I found that mushed elbow I had to replace
 
  #13  
Old 10-07-2011
98_ranger's Avatar
Member
Join Date: Sep 2011
Location: Columbia,SC
Posts: 180
Likes: 0
Received 0 Likes on 0 Posts
when you took your PCV off, did you hear something rattling around in it?
no?
When you start it up, do you have the pedal to the floor to try and keep it running?
tried, but it would still cut off
i'm about to take the bed off this weekend, i think that there is something loose in the tank, because when i changed the fuel pump the second time. i took the tank off. i though it would be easier.. but i was proven wrong
 
  #14  
Old 10-07-2011
04RangerDave's Avatar
JDM> RANGER
iTrader: (3)
Join Date: Jul 2010
Location: RI
Posts: 5,031
Likes: 0
Received 2 Likes on 2 Posts
If the PCV didn't rattle replace it
 
  #15  
Old 10-07-2011
StxDangerRanger's Avatar
RF Veteran
iTrader: (2)
Join Date: Dec 2010
Location: Michigan
Posts: 6,315
Likes: 0
Received 6 Likes on 6 Posts
Originally Posted by 04RangerDave
If the PCV didn't rattle replace it
x2. That may be your problem. your PCV should rattle like a snake.
 
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
thom2003
2.9L & 3.0L V6 Tech
3
04-05-2020 04:00 PM
j_huhnke
General Ford Ranger Discussion
14
04-25-2018 04:58 PM
whiskeybreath
SOHC - 2.3L & 2.5L Lima Engines
1
11-27-2014 04:06 PM
j_huhnke
4.0L OHV & SOHC V6 Tech
2
03-25-2012 09:26 AM
4door
2.9L & 3.0L V6 Tech
7
12-16-2010 11:49 AM



Quick Reply: 03 4.0 idle problem



All times are GMT -6. The time now is 03:29 AM.