Changing an O2 Sensor...?
#1
06-27-2005
Changing an O2 Sensor...?
Got a CEL last weekend... checked it this week is an O2 Sensor (senser 2, bank 1) so my question is, is there a trick to changing these things? Special tool? Procedure? Do they just thread in and plug in? Thanks!
PS.. I know I know, I should know this but its slipped my mind, which side is Bank 1? Left or Right?
PS.. I know I know, I should know this but its slipped my mind, which side is Bank 1? Left or Right?
#3
06-27-2005
#4
06-27-2005
OK the bank one usally is the DRIVER SIDE. but if we cant get claification usally O2 sensors are cheap and you might just want to replace both to be safe.
ok the "special" tool is a O2 sensor socket it has a slot cut in it for the wires really just unplug the O2 sensor FIRST and slip a boxed end wrench over it and it will do the same
Unplug the the O2 Sensor wire(s). Access to the O2 sensor plug(s) may be obscured by the transmission. If you are unable to unplug the O2 sensor(s), the O2 sensor may be removed by CAREFULLY unscrewing the O2 sensors with the wires attached. Note that if you take this short-cut, you run the risk of breaking or twisting off the wires. (Also note that if you opt for this short-cut you will also need to pre-load (twist) the wires so that the wires are not excessively twisted when the O2 sensors are screwed back) Remove the O2 sensors using either a box wrench or a special O2 sensor socket which can be purchased at most auto parts stores. Take care not to drop or jar the O2 sensors.
#5
06-27-2005
Originally Posted by Redneckstone
OK the bank one usally is the DRIVER SIDE. but if we cant get claification usally O2 sensors are cheap and you might just want to replace both to be safe.
ok the "special" tool is a O2 sensor socket it has a slot cut in it for the wires really just unplug the O2 sensor FIRST and slip a boxed end wrench over it and it will do the same
ok the "special" tool is a O2 sensor socket it has a slot cut in it for the wires really just unplug the O2 sensor FIRST and slip a boxed end wrench over it and it will do the same
Ok, Right and Left is typicly gauged by sitting in the driver seat (driver left/passanger right)
I should be able to do it with an open end then...
I dont know about *cheap*, 45bucks each...
#6
06-27-2005
Originally Posted by rngprerunner
Ok, Right and Left is typicly gauged by sitting in the driver seat (driver left/passanger right)
I should be able to do it with an open end then...
I dont know about *cheap*, 45bucks each...
#7
06-27-2005
Originally Posted by Redneckstone
when your talking about engine, you usauly look at it as standing infront of the vehical. but thats always debated about.
DONT ever brake a bolt/sensor loose with a open end you run the risk of striping it. just unplug it and put a closed end on. you get more torque with it.
OUCH i think mine was like $15 or something.
#8
06-27-2005
Originally Posted by rngprerunner
Its allways confused me too.. but all the classes I'v taken I'v learned the *industry standard* is from the driver seat and the applies bumper to bumper...
That would be nice.. if they were that much I'd replace all four.. these things are a rip nowadays...
#9
06-27-2005
Originally Posted by rngprerunner
I know I know, I should know this but its slipped my mind, which side is Bank 1? Left or Right?
Bank:
1= PS
2= DS
Sensor:
1= before cats
2= after cats
So, on a Ranger, since there is only one sensor after the cats, "sensor 2, bank 1" is the single sensor after the cats. (It may be after all of the cats or after some of them, which is the case on most late model Rangers)
In this picture, the Ranger sensor array corresponds to the second drawing down.
Sensor 2, bank 1 is "HO2S 12"
Similarly, spark plug numbering on Fords uses the PS front cylinder for the #1 spark plug. Seems counterintuitive to me but that's Fords convention.
#10
06-27-2005
#11
06-27-2005
Join Date: May 2004
Location: Fuquay Varina, NC
Posts: 3,048
Likes: 0
Received 0 Likes
on
0 Posts
#12
06-27-2005
#14
06-27-2005
Originally Posted by 04 EDGE
i would want to know what the code number is before i wasted money on a sensor that may not be needed
But I used a code reader to get the code... didnt just pull that it needed an O2 sensor out of my *** you know...
#15
06-30-2005
Join Date: Jun 2005
Location: Belleville,MI
Posts: 109
Likes: 0
Received 0 Likes
on
0 Posts
The OEMs are keyed differentl, but it's the exact same sensor for a HEGO or CMS. If you look at the Bosch, who makes the OEM, they put a generic non keyed connector so you can use it front or back. Only difference is the wire lenght.
If you are using an oem the HEGO, pre cat, has a grey connector and the CMS, post cat, will have a blue 80% of the time or a pink/purple connector
I just had to replace the 21 and 22 sensors in my wife's Windstar after doing a tranny swap last week because her 3rd gear one way clutch took a crap at 81k.
If you are using an oem the HEGO, pre cat, has a grey connector and the CMS, post cat, will have a blue 80% of the time or a pink/purple connector
I just had to replace the 21 and 22 sensors in my wife's Windstar after doing a tranny swap last week because her 3rd gear one way clutch took a crap at 81k.
Originally Posted by rwenzing
Just be sure that you get the rear sensor. I think the connector shells are keyed differently and the front O2's won't interchange.
#16
06-30-2005
Join Date: Jun 2005
Location: Belleville,MI
Posts: 109
Likes: 0
Received 0 Likes
on
0 Posts
Thread
Thread Starter
Forum
Replies
Last Post
