Ranger Impact Sensor Part Number?
#1
Ranger Impact Sensor Part Number?
Does anyone have access to a Ford manual for 2001 that would have the part number for the crash impact sensor? The ones that activate the air bags and are behind the bumper. I only found one but I don't want to break it to get it off. Must be another one somewhere.
#3
#4
Originally Posted by rwenzing
Are you sure that what you're looking at is an impact sensor?
According to the info I have, the external sensors were only used until the late 90's. Your 2001 should only have internal sensors within the Restraints Control Module on the transmission tunnel.
According to the info I have, the external sensors were only used until the late 90's. Your 2001 should only have internal sensors within the Restraints Control Module on the transmission tunnel.
http://s121.photobucket.com/albums/o235/DaveO_39/
If someone could tell me how to insert a picture in a message I'd appreciate it.
#5
#6
Originally Posted by 98TexasRanger
That lil bump and your air bags went off???? Wow that sucks. What did your insurance company say/do for you?
Click on the bottom box under the pic.....right click...copy.....go to your post and paste.....it's that easy.
Click on the bottom box under the pic.....right click...copy.....go to your post and paste.....it's that easy.
#8
Originally Posted by DaveO
Wow (embarrassed!) So easy. As for the insurance company, if anyone got paid it was the guy I bought it from. It happened to him and the truck had been sitting since June when it happened and he didn't want to spend (the dealer) money on fixing it. I bought the truck for what I think was a very good price and got some replacement (salvage) air bags and control module. Yet to be put in, but they arrived yesterday.
Speaking of the bumper tilt, anyone have a good idea as to how to best (as in easiest) method to straighten it out? Do I (really) have to remove the bumper and bend/replace a bracket? Everything is pretty rusty under there.
#9
#11
Originally Posted by rwenzing
What I see in the picture looks like the foglamp connector and the ABS wire and a couple of harness runs. I think that the white connector in the middle of the picture might be for the Daytime Running Lamp module which is factory installed on Canadian Rangers only.
Door sticker says Date of MFG: 11/00 Made in USA
#12
Originally Posted by FireRanger
If the wires leading to it aren't bright yellow, it probably isn't part of the airbag system.
I'm hoping it's not an impact sensor because I do have a new air bag module and if that's all I need..
#13
#14
Originally Posted by rwenzing
DRL plug should be:
red/black
light green/yellow
light green/black
purple/orange
black
The Ranger Wiring Manuals show no external crash sensors from 2000MY~2006MY. The sensors are inside the RCM.
red/black
light green/yellow
light green/black
purple/orange
black
The Ranger Wiring Manuals show no external crash sensors from 2000MY~2006MY. The sensors are inside the RCM.
#15
That is kinda strange that the airbags would go off that easily. I read about this in your other post and figured that the bumper would have to have been dented in pretty good to set off the airbag. To my knowledge most airbag sensors are behind the radiator support so when little things like that happen, you dont get a face full of airbag.
#16
Originally Posted by CadiLLaPimPin
That is kinda strange that the airbags would go off that easily. I read about this in your other post and figured that the bumper would have to have been dented in pretty good to set off the airbag. To my knowledge most airbag sensors are behind the radiator support so when little things like that happen, you dont get a face full of airbag.
Thread
Thread Starter
Forum
Replies
Last Post
c0reDump
SOHC - 2.3L & 2.5L Lima Engines
1
10-11-2009 03:50 PM