For Sale: buggman OHC LED panel mod (ky)
#1
buggman OHC LED panel mod (ky)
Some of you already know about these, but I can't seem to find my specific thread on them, so here goes.
My Explorer OHC LED panel mod...
Basically you remove the old bulb holder assembly from your ohc and replace all that old stuff with my led panel. Only 3 wires from the old bulb assembly will need to be cut & attached to the led panel via screw terminals.
Your old screws should be long enough, but I'll include longer screws just in case.
These will fit the style of OHC pictured, but they should also fit the "sunroof" model as well.
These are WAY brighter than the stock bulbs/reflector assembly & are probably brighter than any plug-in LED (they're definitely brighter than the brightest plug-in led's I've found so far).
On to some pics...
(thanks to El Bandito for this pic)
How bright are they???
How about this???
Taken from about 10' away, completely dark garage, only light is the ohc led panel with the lens cover removed.
Here's a LINK to my ohc mods pics where I have more (older) pics as well as my install instructions.
The install should take less than 5 minutes & you'll only need basic hand tools.
Note: NO complete OHC is included, ONLY the led panel mod.
Pricing = $25 +sh/ins/tracking (generally about $7 via priority mail within the USA. Canada shipping will probably be a couple bucks more)
I have a couple ready to go right now so grab 'em before they're all gone!!!
I should also note that my current version of the ohc led panel mod has 60 led's and the actual circuit layout may differ slightly from the old pics as I'm always looking for ways to improve on my design.
The "stock" color will be WHITE but I can do custom versions in Red, Blue, Green & Yellow. I normally paint the circuit board white to help reflect light, but I can paint them in a variety of colors too.
Custom versions will be slightly more expensive & will need to be done on a pre-order basis.
My Explorer OHC LED panel mod...
Basically you remove the old bulb holder assembly from your ohc and replace all that old stuff with my led panel. Only 3 wires from the old bulb assembly will need to be cut & attached to the led panel via screw terminals.
Your old screws should be long enough, but I'll include longer screws just in case.
These will fit the style of OHC pictured, but they should also fit the "sunroof" model as well.
These are WAY brighter than the stock bulbs/reflector assembly & are probably brighter than any plug-in LED (they're definitely brighter than the brightest plug-in led's I've found so far).
On to some pics...
(thanks to El Bandito for this pic)
How bright are they???
How about this???
Taken from about 10' away, completely dark garage, only light is the ohc led panel with the lens cover removed.
Here's a LINK to my ohc mods pics where I have more (older) pics as well as my install instructions.
The install should take less than 5 minutes & you'll only need basic hand tools.
Note: NO complete OHC is included, ONLY the led panel mod.
Pricing = $25 +sh/ins/tracking (generally about $7 via priority mail within the USA. Canada shipping will probably be a couple bucks more)
I have a couple ready to go right now so grab 'em before they're all gone!!!
I should also note that my current version of the ohc led panel mod has 60 led's and the actual circuit layout may differ slightly from the old pics as I'm always looking for ways to improve on my design.
The "stock" color will be WHITE but I can do custom versions in Red, Blue, Green & Yellow. I normally paint the circuit board white to help reflect light, but I can paint them in a variety of colors too.
Custom versions will be slightly more expensive & will need to be done on a pre-order basis.
#3
Small update:
I have one "blemished" ohc led panel I was working on... but it kinda fell off my work table & chipped part of the pcb off.
I couldn't let it go to waste so I installed 48 led's in it & wired it up as I do with my others.
Once installed, the blemish on the side doesn't actually show (I'll try to get pics of it tonight) and it's still really bright.
For this one "blemished" ohc led panel, I'm discounting it down to $20.00 +sh/ins/tracking. Just have the one oops panel, but I have a few of my normal quailty led panels ready to go
I'll update the thread if someone jumps on the blemished one or if I run low on the regular ones.
Pics of blem:
I have one "blemished" ohc led panel I was working on... but it kinda fell off my work table & chipped part of the pcb off.
I couldn't let it go to waste so I installed 48 led's in it & wired it up as I do with my others.
Once installed, the blemish on the side doesn't actually show (I'll try to get pics of it tonight) and it's still really bright.
For this one "blemished" ohc led panel, I'm discounting it down to $20.00 +sh/ins/tracking. Just have the one oops panel, but I have a few of my normal quailty led panels ready to go
I'll update the thread if someone jumps on the blemished one or if I run low on the regular ones.
Pics of blem:
Last edited by buggman; 05-21-2013 at 11:57 PM.
#9
Holy long time no bump batman!
Thought I better update this thread.
After a difficult year I finally have a few of these bad boys done. I've been continually improving the design since I started & these are what may be the last of the 2014 models.
I've been painting the PCB's silver for a while now, seems like it gives a little extra reflection.
I also have this ONE 60x led model that I started earlier in the year & just finished up.
It doesn't have voltage regulators like the regular ones but I've ran them all up to 15vdc for several hours & have had NO issues with them at all.
It does have a little white paint overspray on the back where I forgot to mask it off when I did some touch up on the front... doesn't hurt anything & you won't even see it when installed
I'll let this one 60x led model go for the regular OHC LED panel price of $25 +sh (generally about $5.50 priority mail flat rate insured with tracking #)
The install is still just as easy as the originals, here's a LINK to my photobucket album with the instructions.
These are all my 5mm LED versions, on rare occasions like when I have complete ohc's to mod, I'll upgrade to a newer style of SuperFlux LED's... they're even brighter & have a wider viewing angle but are much more expensive than the 5mm led's. If you'd like one of the mega stupid bright SuperFlux LED versions (not that the 5mm led versions aren't bright... they'll blow away any plug-in led) let me know & we'll discuss.
Thought I better update this thread.
After a difficult year I finally have a few of these bad boys done. I've been continually improving the design since I started & these are what may be the last of the 2014 models.
I've been painting the PCB's silver for a while now, seems like it gives a little extra reflection.
I also have this ONE 60x led model that I started earlier in the year & just finished up.
It doesn't have voltage regulators like the regular ones but I've ran them all up to 15vdc for several hours & have had NO issues with them at all.
It does have a little white paint overspray on the back where I forgot to mask it off when I did some touch up on the front... doesn't hurt anything & you won't even see it when installed
I'll let this one 60x led model go for the regular OHC LED panel price of $25 +sh (generally about $5.50 priority mail flat rate insured with tracking #)
The install is still just as easy as the originals, here's a LINK to my photobucket album with the instructions.
These are all my 5mm LED versions, on rare occasions like when I have complete ohc's to mod, I'll upgrade to a newer style of SuperFlux LED's... they're even brighter & have a wider viewing angle but are much more expensive than the 5mm led's. If you'd like one of the mega stupid bright SuperFlux LED versions (not that the 5mm led versions aren't bright... they'll blow away any plug-in led) let me know & we'll discuss.
#10
PM sent to get this one 60x led model go for the regular OHC LED panel price of $25 +sh (generally about $5.50 priority mail flat rate insured with tracking #)
If it is not already spoken for.
If it is not already spoken for.
Thread
Thread Starter
Forum
Replies
Last Post
buggman
OLD - Interior, Exterior, Electrical, & Misc.
3
02-19-2015 12:47 PM
buggman
OLD - Interior, Exterior, Electrical, & Misc.
45
04-06-2014 08:15 AM
buggman
OLD - Interior, Exterior, Electrical, & Misc.
82
03-31-2014 12:33 AM
buggman
OLD - Interior, Exterior, Electrical, & Misc.
62
09-29-2012 11:25 PM