For Sale: FS: Custom Blacked Tail Lights - IN
#1
FS: Custom Blacked Tail Lights - IN
Very glossy, look great. Very Dark. Buyer will be advised to purchase LEDs for brakes so they shine through well. You can see tail lights but it's somewhat dim.
Off of a 2003 ranger tremor stepside. Tail light are supposedly the same between truck beds. $125 obo.
Pm w questions.
Off of a 2003 ranger tremor stepside. Tail light are supposedly the same between truck beds. $125 obo.
Pm w questions.
#5
Member
iTrader: (4)
Join Date: Oct 2010
Location: carrollton, ga
Posts: 217
Likes: 0
Received 0 Likes
on
0 Posts
RANGER OEM BLACK SMOKED OUT TAIL LIGHT TINTED REAR LAMP: eBay Motors (item 300478197364 end time Nov-06-10 19:43:15 PDT)
link ^^
#6
they are just stock painted tails
RANGER OEM BLACK SMOKED OUT TAIL LIGHT TINTED REAR LAMP: eBay Motors (item 300478197364 end time Nov-06-10 19:43:15 PDT)
link ^^
RANGER OEM BLACK SMOKED OUT TAIL LIGHT TINTED REAR LAMP: eBay Motors (item 300478197364 end time Nov-06-10 19:43:15 PDT)
link ^^
#7
Also, they suck at painting with niteshades. Mine look just as glossy as his that didn't use VHT niteshades. The only way niteshades looks that bad is if you do several light coats. You need to keep spraying until it's wet. Takes awhile to master. My new LED tails are VHT niteshaded and are flawless.
#13
Yep I have painted many and done well. There's a few tricks though. The runs are certainly an issue!
#14
1. pull my tail lights out of my truck
2. clean off with windex
3. spray on 3-4 light coats of the vht nightshade
4. let dry for 2-3 hours just in case
5. put back in truck
#15
before i did my lights i watched a "how to" video to see if there is anything special and the guy listed like 15 steps. when i did mine all i did was
1. pull my tail lights out of my truck
2. clean off with windex
3. spray on 3-4 light coats of the vht nightshade
4. let dry for 2-3 hours just in case
5. put back in truck
1. pull my tail lights out of my truck
2. clean off with windex
3. spray on 3-4 light coats of the vht nightshade
4. let dry for 2-3 hours just in case
5. put back in truck
I do two thick coats, or one thick coat. Runs become an issue but if you mess up you can quickly remove the VHT you sprayed with windex and a towel if you catch it quick enough. They lay much glossier if you do thick coats. I've painted 10+ sets with thick coats, all look A1, and 20+ in thin coats, I'd say 1 in 5 come out well. That may just be me.
#16
i have had it turn out flat and glossy. The two rangers I have done have both turned out glossy through the light coats except for the third brake light. I have done it on an s-10 with doing the same methods and it has turned out flat. i think it all depends on the texture of the tail lights and also how well you prep the lights before you spray em'
Thread
Thread Starter
Forum
Replies
Last Post
Taylor
OLD - Interior, Exterior, Electrical, & Misc.
3
07-01-2012 07:55 PM
dtcercado
OLD - Interior, Exterior, Electrical, & Misc.
1
09-28-2010 10:09 PM
Want to Trade: Euro Tail Lights for 06+ Tail Lights
Masteratarms93
OLD - Interior, Exterior, Electrical, & Misc.
0
07-19-2010 11:29 PM