center console design picture
#1
center console design picture
its a rough idea/work in progress if i ever do a bucket seat install. not sure how it could be constructed (ideas would be helpful ). the top portion/arm rest area is right about the stock armrest height, and i would come up with a hinged top design similar to the stock, but obviously with more room underneath. my truck is a 5spd so i do have the factory cup holders mounted by the shifter, however, i usually have the ashtray filled with coins in one cup, and stuff in the other and can always benefit from more cup holders. the other 2 openings would be for...stuff...
any input/advice would be much appreciated.
EDIT..it is dimensioned to fit between the shifter with proper clearance, and the rear deck (standard cab) however it may get notched to go all the way back and molded into a sub box of some sort...
any input/advice would be much appreciated.
EDIT..it is dimensioned to fit between the shifter with proper clearance, and the rear deck (standard cab) however it may get notched to go all the way back and molded into a sub box of some sort...
#3
Originally Posted by slammer67
how about this
Not quite finished with the drawing, but you get the idea. I'll lose access to my ash tray and cig lighter, but I'll put some 12v recepts in the console somewhere.
Not quite finished with the drawing, but you get the idea. I'll lose access to my ash tray and cig lighter, but I'll put some 12v recepts in the console somewhere.
#6
#7
Just an idea here but what if you take the gray one and make a drawer in it? The upper section would be a good place for it. The curved surface at the front would be the front of the drawer. I know I hate lifting the cover on my armrest. Sometimes it's a pain to close cause it's so far back.
The probelm I see with having a hinged cover that opens on the side is if someone in the passenger side needs to get in it.
An idea I like with my S-10 was the cup holder inserts. Inserts fit small cups and can be removed for cleaning when the coffee splashes on those sudden stops. Also you can remove it if you have cups with large bottms but of course now your hand and a rag can fit to clean them out.
If you have an MP3 player and an extented cab you could put a drawer in the lower section that opens rearwards since MP3 CDs don't need changing as often. (I get about 20 CDs per MP CD)
Is the one with the blue cushion done on Max3D?
The probelm I see with having a hinged cover that opens on the side is if someone in the passenger side needs to get in it.
An idea I like with my S-10 was the cup holder inserts. Inserts fit small cups and can be removed for cleaning when the coffee splashes on those sudden stops. Also you can remove it if you have cups with large bottms but of course now your hand and a rag can fit to clean them out.
If you have an MP3 player and an extented cab you could put a drawer in the lower section that opens rearwards since MP3 CDs don't need changing as often. (I get about 20 CDs per MP CD)
Is the one with the blue cushion done on Max3D?
#8
Originally Posted by jbomb212
Not bad i would just make the top have a compartment with a lid(for CDs and junk).........by the way is this done in Solidworks???? Just wondering, i use that about half the time at work the other half is autocadd
Originally Posted by Victory
Just an idea here but what if you take the gray one and make a drawer in it? The upper section would be a good place for it. The curved surface at the front would be the front of the drawer. I know I hate lifting the cover on my armrest. Sometimes it's a pain to close cause it's so far back.
The probelm I see with having a hinged cover that opens on the side is if someone in the passenger side needs to get in it.
An idea I like with my S-10 was the cup holder inserts. Inserts fit small cups and can be removed for cleaning when the coffee splashes on those sudden stops. Also you can remove it if you have cups with large bottms but of course now your hand and a rag can fit to clean them out.
If you have an MP3 player and an extented cab you could put a drawer in the lower section that opens rearwards since MP3 CDs don't need changing as often. (I get about 20 CDs per MP CD)
The probelm I see with having a hinged cover that opens on the side is if someone in the passenger side needs to get in it.
An idea I like with my S-10 was the cup holder inserts. Inserts fit small cups and can be removed for cleaning when the coffee splashes on those sudden stops. Also you can remove it if you have cups with large bottms but of course now your hand and a rag can fit to clean them out.
If you have an MP3 player and an extented cab you could put a drawer in the lower section that opens rearwards since MP3 CDs don't need changing as often. (I get about 20 CDs per MP CD)
Thanks for the input.
#11
#12
Mine was done with Rhinoceros 3D. It's not my fav design,but I planned it around the shifters, putting the quicksilvershifter at the best spot to shift while 4-wheelin. I'm going to put some sort of mp3 mount in there somewhere as well as a mount for the sirius reciever. There's not much room to work with as there's only about 6-1/2" between the seats, that's why I built it to come up to the dash and cover the ash tray. I wanted to put a CB in there, but there wasn't room. Maybe I'll go with one that has the controls in the handset and mount it on the side or something.
#14
Thread
Thread Starter
Forum
Replies
Last Post
jtkonieczny
Interior Semi-Tech
11
11-08-2011 05:21 PM
gibsondale
General Ford Ranger Discussion
3
04-20-2010 09:03 AM