1 TON RANGER
#1
1 TON RANGER
hey guys i dont post on here much but i got a set of dodge 1 tons you think i should use this for my sas or should i just flip them for something else my plans are to go 1 tons leafs and 38s of course gears and all the other things that go along with the sas could really use your guys help with this delema
#3
#4
the passenger side has a disconnect in the tube and a 2 piece shaft. you would have to retube the pass side and find an older set of ball joint knuckles to get rid of the unit bearings. then you have to cut off the coil setup and mount some leaf perches. if you got it for free then it might be worthwhile to do that. if you retube it then just make sure you make it the same length as a factory shaft that way its easier to get a spare.... or you could just sell the front and find an axle out of a 78-79 f250 or 350 AND they already run leafs. that would be my choice. ford d44's are easy to find but 60's are kinda tough
#5
i know about the disconect i think im just gunna clip them or try and trad for a eb front end or just run them the truck had 50xxx miles on it so ther not to bad of shape just kinda tuff decision since im on a really tight buget i know this is off the wall coul i run the whole coil spring set up and make a radis arm set up kinda like the do with the do 30? ive never built a ranger or link system before thats kinda why i was leaning tworads a leaf set up
#6
I'd stay away from anything under a dodge without a spin tech kit. Ford unit bearings are better and you get lockouts. And spider trax makes aftermarket units in 5 bolt. Anyway, I'd just clean it then flip the thing and find an eb like you were saying, nothing wrong with free!
Last edited by bfd's_ranger; 05-06-2012 at 07:09 PM.
#9
#11
yup, they started with discs in 76. i actually have a eb front and 2 9 inch rears. they need to be rebuilt and i cut the wedges off to do a 3 link but you can buy new ones i think from bronco graveyard. FOR SALE
#13
does it have any goodies? IE: l/s or locker, desirable gears, upgraded shafts etc...
i bought my eb with an open carrier, a trac loc, 2 sets of gears, 2 sets of stock lockouts, a pair of stock shafts, new rotors, and other misc. parts for 250. and both my small bearing and big bearing 9's for 250 each. one had 3.50's and the other 4.11's
i bought my eb with an open carrier, a trac loc, 2 sets of gears, 2 sets of stock lockouts, a pair of stock shafts, new rotors, and other misc. parts for 250. and both my small bearing and big bearing 9's for 250 each. one had 3.50's and the other 4.11's
#14
So you want him to ditch a working set of 1 tons for a 40 year old D44...I'm sorry weak or not the dodge unit bearing D60 is more than strong enough for 38s. The CAD can be deleted and there is a spinfree kit for the unit bearing hubs. I personally think they will be fine seeing how they survive with a 1200lbs cummins sitting above them.
#16
Anyways, EB44 is better than Ddoge D60. Just cause it's easy as heck to install on a ranger.
#17
#19
well got another update have a new job that requires alot of driveing and i dont see gas/ diesel prices dropping soon question is i found a 44/9 inch combo the 9 inch has 456s lockers yukon axles and the front end is the same deal. can i run the 9 inch or will i run into roblems with vss?
Thread
Thread Starter
Forum
Replies
Last Post
Fx4wannabe01
General Ford Ranger Discussion
2
10-25-2007 07:28 PM
Wowak
General Ford Ranger Discussion
24
08-24-2004 08:12 PM