everyy thing i need?
#1
#2
#7
you'll need 11.25" rotors that will fit an 02 ranger.
However, I'm not sure of the other braking system components. I'd like to assume your calipers, etc will be the same. Assuming they are the same, then again, from the kit all you'll need extra will be the 11.25" rotors.
Given you're an 07 you shouldn't need a new front drive shaft right away, but do save up for one. You may also want different wheels at a later date.
The kit calls for wheels with a 4in back spacing. HOWEVER, I called RCD last month and asked them about that. The alcoas with their 4.5" backspacing will work fine. I will be getting wheels shortly though as I'd prefer a wider stance since I'm going up in height. The idea is to offset at least some of the change in center of gravity, though it probably won't be much. The question I have to answer for myself though, is do I want to keep running 33s or so I want to go up to 35s? I'll be geared to 4.88, which is a little low, but it gives me some room if I go larger. I just don't want to put a body lift on, which is what might be needed to run the 35s. Of course there's always front glass and pulled bed sides!
However, I'm not sure of the other braking system components. I'd like to assume your calipers, etc will be the same. Assuming they are the same, then again, from the kit all you'll need extra will be the 11.25" rotors.
Given you're an 07 you shouldn't need a new front drive shaft right away, but do save up for one. You may also want different wheels at a later date.
The kit calls for wheels with a 4in back spacing. HOWEVER, I called RCD last month and asked them about that. The alcoas with their 4.5" backspacing will work fine. I will be getting wheels shortly though as I'd prefer a wider stance since I'm going up in height. The idea is to offset at least some of the change in center of gravity, though it probably won't be much. The question I have to answer for myself though, is do I want to keep running 33s or so I want to go up to 35s? I'll be geared to 4.88, which is a little low, but it gives me some room if I go larger. I just don't want to put a body lift on, which is what might be needed to run the 35s. Of course there's always front glass and pulled bed sides!
#8
here's more info for you.......
read the stickies at the top. it's ALL RCD questions!
http://www.offroadrangers.com/forum/...splay.php?f=15
read the stickies at the top. it's ALL RCD questions!
http://www.offroadrangers.com/forum/...splay.php?f=15
#11
check this out........
http://www.drivewire.com/percatalog/...IFT%20KIT&pt=4
open 2 browsers....
do RCD for 1 and superlift for other
RCD is cheaper! hahahaha
Thing that gets me is it says for 2wd, even when clicking on 4 wheel drive navigation to get there.
http://www.drivewire.com/percatalog/...IFT%20KIT&pt=4
open 2 browsers....
do RCD for 1 and superlift for other
RCD is cheaper! hahahaha
Thing that gets me is it says for 2wd, even when clicking on 4 wheel drive navigation to get there.
Thread
Thread Starter
Forum
Replies
Last Post
1dustinlthomas
4.0L OHV & SOHC V6 Tech
3
04-20-2010 10:58 PM
Tys 4x4 FTW
General Ford Ranger Discussion
19
11-14-2009 08:31 PM
winks
General Technical & Electrical
9
05-13-2008 01:27 PM
helliboarder
General Ford Ranger Discussion
2
10-03-2004 10:13 PM