Will these get my Ranger even
#1
Will these get my Ranger even
I have a 2002 Ranger XLT 4.0 and I have a sagging issue in the front. My truck has brand new OEM shocks up there but it still has a little sag. Since my tbars are 12 years old, I am considering upgrading to new "#1 bars" that are apparently stiffer than the ones I have. Also, they should get me back to an even lift (about 2 in) in the front.
It's a 3 inch body lift on 33's. Everything else is stock. Will these tbars give me 2 inches or so without cranking? And if I crank them, will I get the front taller than the back?
Here's how she looks now:
These are the bars that supposedly will give me more lift:
Torsion Bar for 2002 Ford Ranger|F67Z-5B326-FA
Torsion Bar for 2002 Ford Ranger|F67Z-5B326-FB
answers are much appreciated
It's a 3 inch body lift on 33's. Everything else is stock. Will these tbars give me 2 inches or so without cranking? And if I crank them, will I get the front taller than the back?
Here's how she looks now:
These are the bars that supposedly will give me more lift:
Torsion Bar for 2002 Ford Ranger|F67Z-5B326-FA
Torsion Bar for 2002 Ford Ranger|F67Z-5B326-FB
answers are much appreciated
#2
Like I've tried to tell you.. It depends on how much your truck has sagged....
Even with #1 bars I'm sure you will have to crank them some to make it level with your factory rear end.
Even trucks that came with the #1 bars from the factory had a rake (with bars at factory height) - so your truck wouldn't be any different...
If you then crank them, it would be level...Like everyone else has done since 1998.
Even with #1 bars I'm sure you will have to crank them some to make it level with your factory rear end.
Even trucks that came with the #1 bars from the factory had a rake (with bars at factory height) - so your truck wouldn't be any different...
If you then crank them, it would be level...Like everyone else has done since 1998.
Last edited by logan03CO; 06-29-2014 at 01:50 PM.
#3
#4
What I'm trying to tell you is this:
Not a single Ranger came from the factory leveled from front to rear - the type of torsion bar used didn't matter - they all had a designed rake to them from the factory floor.
If the entire truck was brand new with 0 miles & you wanted it level - a person would have to crank the torsion bars. No way around it.
So, armed with that information.....one can easily figure out that if you were to replace your torsion bars with brand new ones - you would also need to crank them to your truck level with your factory rear end.
The rating of torsion bar (1 vs B vs F) really only comes into play with talking 'resistance' to sagging over time.
#5
Like I've tried to tell you.. It depends on how much your truck has sagged....
Even with #1 bars I'm sure you will have to crank them some to make it level with your factory rear end.
Even trucks that came with the #1 bars from the factory had a rake (with bars at factory height) - so your truck wouldn't be any different...
If you then crank them, it would be level...Like everyone else has done since 1998.
Even with #1 bars I'm sure you will have to crank them some to make it level with your factory rear end.
Even trucks that came with the #1 bars from the factory had a rake (with bars at factory height) - so your truck wouldn't be any different...
If you then crank them, it would be level...Like everyone else has done since 1998.
Nobody can have an exact answer for you because every truck is different as far as potential 'sag' over time goes....
What I'm trying to tell you is this:
Not a single Ranger came from the factory leveled from front to rear - the type of torsion bar used didn't matter - they all had a designed rake to them from the factory floor.
If the entire truck was brand new with 0 miles & you wanted it level - a person would have to crank the torsion bars. No way around it.
So, armed with that information.....one can easily figure out that if you were to replace your torsion bars with brand new ones - you would also need to crank them to your truck level with your factory rear end.
The rating of torsion bar (1 vs B vs F) really only comes into play with talking 'resistance' to sagging over time.
What I'm trying to tell you is this:
Not a single Ranger came from the factory leveled from front to rear - the type of torsion bar used didn't matter - they all had a designed rake to them from the factory floor.
If the entire truck was brand new with 0 miles & you wanted it level - a person would have to crank the torsion bars. No way around it.
So, armed with that information.....one can easily figure out that if you were to replace your torsion bars with brand new ones - you would also need to crank them to your truck level with your factory rear end.
The rating of torsion bar (1 vs B vs F) really only comes into play with talking 'resistance' to sagging over time.
Boom.
#7
#8
Join Date: Apr 2007
Location: Placentia, CA
Posts: 927
Likes: 0
Received 0 Likes
on
0 Posts
Yes you can crank them still. Superlift essentiall "drops" the front suspension components while raising the truck. The negative blowbacks are faster wearing front end parts, but bigger tires does this too.
Thread
Thread Starter
Forum
Replies
Last Post
DetroitStyle
Project Logs
30
11-03-2009 08:00 PM
VulcanMotor~PowerHouse
Interior Semi-Tech
25
12-04-2005 12:41 AM