so my s10 is up for sale right now because its a money pit, but it has these rims on it and i dont really wanna sell em if they fit.
my stupid computer is being gay and i cant post oa picture of the Bronco2 with 35's i was originally going to post.. so here's a pic of my s15 (4x4 3" body lift) with the rims on it.



best pic i could find.

cliff notes as im on my 4th beer in an hour..haha no im not a cheap drunk either hehe.

- picture is of
-will these rims fit my 1993 ranger XLT


if they fit, im swapping them onto my ranger because i like the rims, and because they have better rubber than what i got now. i have a set of stock s10 rims, also have a set of rubbers i can swap over to the s10 rims just dont have the money right now to do so at this moment..

just wanna know if these rims will fit.. thanks..

EDIT: haha sorry guys forgot the picture!!!

 

You say they are currently on a BII?

If so, they should be the 5on4.5 bolt pattern so that would be good to go...

Now the only thing you need to check is the hole in the middle for the hub. Your truck should have a D35 front axle whereas the BII has a D28. The D35 hub is larger in diameter than the D28, so you may have issues...

could you get the pics on here?

 

chevy pattern is different

 

thats what i was thought. i have the exact rims can i make them fit?? without fudging too much fudging.???
i have tried these rims on my ranger and they are off by like a 1/4" or less... just wanted to see if they fit.


to the above post.. NO this is not my B2. sorry if i gave the wrong info...

 

i'll try right now as i have nothing else to do... haha

 

if u want ur wheel flying off then go ahead and put them on lol

 

why is that??? not trying to be dick or anything... just curious??

just startin' up the laptop and it should let me save the B2 pics onto my comp then to save and post em. hopefully.

 

 

only way you can do it is if you get wheel adapters which i wouldn't run lol. i rather not snap a stud and then have my wheel fly off
....or get them re-drilled which will cost you more for 1 wheel than all of them are worth lol

btw i want the red truck lol

 

it doesnt matter if its a 1/8" difference its the WRONG BOLT PATTERN.

 

haha thats what i thought...

700 bucks and its urs... im bored so i'll give u the specs

88 GMC Sierra S15 4x4. 2 door ext'd cab, manual t-case, 4wd, needs rear bumper (have a stock front bumper to go with the truck) needs bell housing... 2. 8L 5 speed.. set of stock s10 rims in the back of the p/u for it.. needs a few things. cracked bell housing, if sold local (within 10kms) i will drive it there) has no insurance etc... blag blah blah..

I bought it at the end of august of 2003 for a project.had big plans for it (SAS, 39.5" rubber) wasnt worth it to me on a pissy little truck.. was/is my first vehicle when i was 15, bought as a project, but now i need the money more than anything.. want to eventually get another ford..cuz i hate chevy..have a spare 2.8L with a blown connecting rod bearing in it sitting in the shed, not sure if i wasnt to sell it yet... just waitin for the right person haha..

oh and NO shipping..gotta pick the some *****.

 

thanks redneckstone!!!

 

got the picture of rims that are the Bll

 

Ah, gotcha... I thought you were talking about the first set earlier... LOL

If you notice on the BII, there is very little room for the hub to come out (look at front tires)... The hubs on your D35 might not fit through there since they are a larger diameter than the BII's D28

 

ic ic thanks.. thats what i was wondering!

 

hahaha nice drawing!!!!! haha.lol