2.9L & 3.0L V6 Tech General discussion of 2.9L and 3.0L V6 Ford Ranger engines.

3.0 missfire and rough shaking

Thread Tools
 
Search this Thread
 
  #1  
Old 10-05-2008
manofak's Avatar
Member
Thread Starter
Join Date: Nov 2007
Location: elk grove, IL
Posts: 225
Likes: 0
Received 0 Likes on 0 Posts
3.0 missfire and rough shaking

ok guys i started my 2000 xlt with the 3.0 and it started to shake the whole truck. it would stop above 1500rpm but now its all the time. my brother said its the injector since we know its the #5 cylinder and we replaced plugs and wires and tested them and they work fine. so i guess its my injector, but earlier i started it up and it is cold outside but my exhaust was abit white. i dont know if it was because of the cold or if maybe im burning colant. do you think seafoam would help fix the injector or would i have to take it out and have it cleaned? (my brother works at a diesel fuel injection shop so i'll have him clean it) or do you think that a blown head gasket might cause this? and when i smelled the exhaust this morning it smelled alot like gas fumes so i think the #5 injector is stuck open. any help or anything would be great thanks in advance.
 
  #2  
Old 10-05-2008
ONERANGER's Avatar
Member
Join Date: Oct 2008
Location: lancaster, ca
Posts: 5
Likes: 0
Received 0 Likes on 0 Posts
check your mass air flow sensor my truck was doing similar things i cleaned out the M.A.F. and it was good. maybe start there before you pull the heads
 
  #4  
Old 10-05-2008
manofak's Avatar
Member
Thread Starter
Join Date: Nov 2007
Location: elk grove, IL
Posts: 225
Likes: 0
Received 0 Likes on 0 Posts
yep its flex fuel
 
  #5  
Old 10-05-2008
manofak's Avatar
Member
Thread Starter
Join Date: Nov 2007
Location: elk grove, IL
Posts: 225
Likes: 0
Received 0 Likes on 0 Posts
i tried cleaning the maf and now it only shakes at low rpms but its still putting out whitesmoke
 
  #6  
Old 10-06-2008
Hot Wheels's Avatar
Member
Join Date: Oct 2006
Location: Maple Plain, MN
Posts: 211
Likes: 0
Received 1 Like on 1 Post
I had this happen to me twice. Both times it was an injector. You can try cleaning it, it didn't work for me, but one was an electronic failure. No amount of cleaning would save it. Hope you get it fixed.
 
  #7  
Old 10-06-2008
Ranger0n20s's Avatar
Member
Join Date: Oct 2006
Location: Mandeville, Louisiana
Posts: 387
Likes: 0
Received 0 Likes on 0 Posts
mm cold outside... shakes around idle and its white smoke out the exhaust... i believe its a injector.... try sea foam and see if that breaks up the deposit on the injectors... if that doesnt help i say take the injectors off and see whats going on inside the injector.
 
  #8  
Old 10-06-2008
Earl43P's Avatar
Member
Join Date: Nov 2005
Location: Elizabeth City, NC
Posts: 767
Likes: 0
Received 4 Likes on 3 Posts
  #9  
Old 10-06-2008
manofak's Avatar
Member
Thread Starter
Join Date: Nov 2007
Location: elk grove, IL
Posts: 225
Likes: 0
Received 0 Likes on 0 Posts
i thought about sea foaming, does anyone know where a how-to would be to do it?
 
  #10  
Old 10-06-2008
Ranger0n20s's Avatar
Member
Join Date: Oct 2006
Location: Mandeville, Louisiana
Posts: 387
Likes: 0
Received 0 Likes on 0 Posts
its easy man... just pour 1/3 into a full tank of gas, run it for about 5-10min and thats it.....


- for me i usually sea foam b4 i do a oil change so i also pour 1/3 into the brake booster and in the oil itself and let it run and watch all the smoke come out the tailpipe. once it clears up then its done and i change the oil and the filter.
 
  #11  
Old 10-07-2008
manofak's Avatar
Member
Thread Starter
Join Date: Nov 2007
Location: elk grove, IL
Posts: 225
Likes: 0
Received 0 Likes on 0 Posts
into a full tank of gas!?!?!?!?! nice joke i cant afford half a tank jk, i'll try thursday thanks! :D
 
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Jack_RANGER
2.9L & 3.0L V6 Tech
5
02-04-2021 03:27 PM
sturgill
4.0L OHV & SOHC V6 Tech
5
10-08-2012 02:34 PM
PwrRngr
4.0L OHV & SOHC V6 Tech
1
06-05-2009 11:38 AM
Frank91
2.9L & 3.0L V6 Tech
13
01-30-2009 01:59 AM
enkaarob
4.0L OHV & SOHC V6 Tech
4
03-03-2008 06:45 PM



Quick Reply: 3.0 missfire and rough shaking



All times are GMT -6. The time now is 06:34 PM.