4.0L OHV & SOHC V6 Tech General discussion of 4.0L OHV and SOHC V6 Ford Ranger engines.

No spark and no fault code ???

Thread Tools
 
Search this Thread
 
  #1  
Old 04-26-2011
metalmole's Avatar
Member
Thread Starter
Join Date: Apr 2011
Location: Fayetteville N.C.
Posts: 5
Likes: 0
Received 0 Likes on 0 Posts
No spark and no fault code ???

Like it says, My 99 4.0 auto trans ranger has 165000 on the clock. This morning went out and it will not start, been a daily driver and had no problems. Engine spins over good, but no spark an checking for fault codes brings nothing up. Any ideas...........
 
  #2  
Old 04-26-2011
04RangerDave's Avatar
JDM> RANGER
iTrader: (3)
Join Date: Jul 2010
Location: RI
Posts: 5,031
Likes: 0
Received 2 Likes on 2 Posts
check your coil
 
  #3  
Old 04-27-2011
metalmole's Avatar
Member
Thread Starter
Join Date: Apr 2011
Location: Fayetteville N.C.
Posts: 5
Likes: 0
Received 0 Likes on 0 Posts
Is there anywhere on the fourm that goes over checking the coil, I did a search but couldnt find anythinh.............Thanks
 
  #4  
Old 04-27-2011
04RangerDave's Avatar
JDM> RANGER
iTrader: (3)
Join Date: Jul 2010
Location: RI
Posts: 5,031
Likes: 0
Received 2 Likes on 2 Posts
Do a spark test. review results
Pull the plug on the coil and see if its getting 12v while starting review results
test for a switching signal on the back of the connector back probe it (ICM switching ON/OFF)
 

Last edited by 04RangerDave; 04-27-2011 at 06:32 AM.
  #5  
Old 04-27-2011
metalmole's Avatar
Member
Thread Starter
Join Date: Apr 2011
Location: Fayetteville N.C.
Posts: 5
Likes: 0
Received 0 Likes on 0 Posts
its full of gas, I just checked the fuel pressure, its at 60 psi.
 
  #6  
Old 04-27-2011
04RangerDave's Avatar
JDM> RANGER
iTrader: (3)
Join Date: Jul 2010
Location: RI
Posts: 5,031
Likes: 0
Received 2 Likes on 2 Posts
Originally Posted by metalmole
its full of gas, I just checked the fuel pressure, its at 60 psi.
do what i mentioned above
 
  #7  
Old 04-27-2011
metalmole's Avatar
Member
Thread Starter
Join Date: Apr 2011
Location: Fayetteville N.C.
Posts: 5
Likes: 0
Received 0 Likes on 0 Posts
I gonna have to get some info on how to check the coil, I would think if its good I should also check the crank pos sensor.
 
  #8  
Old 04-27-2011
04RangerDave's Avatar
JDM> RANGER
iTrader: (3)
Join Date: Jul 2010
Location: RI
Posts: 5,031
Likes: 0
Received 2 Likes on 2 Posts
i would bet its the coil.
 
  #9  
Old 04-27-2011
metalmole's Avatar
Member
Thread Starter
Join Date: Apr 2011
Location: Fayetteville N.C.
Posts: 5
Likes: 0
Received 0 Likes on 0 Posts
Just checked the coil pulsing and found its not, checked the crank position sensor and found it was rubbing the gear, adjusted it and the engine fired right up !! thanks
 
  #10  
Old 05-14-2011
boatmoter's Avatar
Member
Join Date: May 2011
Location: Tampa Fl.
Posts: 23
Likes: 0
Received 0 Likes on 0 Posts
CHECK TO SEE IF YOUR TACH IS WORKING WHEN CRANKING,CHECK TO SEE IF YOU HAVE INJECTOR PULSE, IF YOU DON'T HAVE THESE THROW A CRANK SENSOR AT IT..
 
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Best4x4
DOHC - 2.3L Duratec / Mazda L Engines
7
09-04-2008 11:48 AM
Jeremy102579
General Technical & Electrical
1
11-12-2006 12:52 PM
Jeremy102579
General Technical & Electrical
2
11-10-2006 01:42 PM
TheBob
4.0L OHV & SOHC V6 Tech
8
08-30-2005 01:07 AM



Quick Reply: No spark and no fault code ???



All times are GMT -6. The time now is 11:40 PM.