dual voice coil 4ohm sub = 4ohm out?
#1
#2
this is my amp:
http://www.sonicelectronix.com/item_...k+LT980-2.html
Would it be better to just wire each voice coil to the different channels?
http://www.sonicelectronix.com/item_...k+LT980-2.html
Would it be better to just wire each voice coil to the different channels?
#3
#5
Series the coils, and bridge the amp to the now "single" voicecoil sub.
If you wire each coil in stereo, the coils could fight eachother electrically if the left and right channels are destructively interfering.
Bridging the amp into an 8 ohm load will give you the same power output as running 2 independent 4 ohm speakers.
#6
No - don't do this.
Series the coils, and bridge the amp to the now "single" voicecoil sub.
If you wire each coil in stereo, the coils could fight eachother electrically if the left and right channels are destructively interfering.
Bridging the amp into an 8 ohm load will give you the same power output as running 2 independent 4 ohm speakers.
Series the coils, and bridge the amp to the now "single" voicecoil sub.
If you wire each coil in stereo, the coils could fight eachother electrically if the left and right channels are destructively interfering.
Bridging the amp into an 8 ohm load will give you the same power output as running 2 independent 4 ohm speakers.
Last edited by Takeda; 02-22-2009 at 06:10 PM.
#7
I had mine set up this way for a long time until I finally bought single voice coil 4ohm subs.
#8
Power = V*V/R
....and this is where the 8 OHM is going to kill your power, even if the amp is bridged......
#9
To the OP: I suggest you email the manufacturer of the amp and ask.
#10
#11
and oh.. 12volt agree's with me...
http://www.the12volt.com/caraudio/wo...s.asp?Q=1&I=42
Last edited by Jp7; 02-22-2009 at 06:46 PM.
#12
Not when you're talking about AC current on an inductive load.
It doesn't matter which way you wire it, really. Personally I'd do 8ohm one channel because high voltage low current means impedance rise is lower proportionally.
It doesn't matter which way you wire it, really. Personally I'd do 8ohm one channel because high voltage low current means impedance rise is lower proportionally.
#14
#15
determine current, and total power....With an inductive load, as frequency goes up, current is going to decrease.
#16
Just an engineering degree... so b*** me buddy..
and oh.. 12volt agree's with me...
http://www.the12volt.com/caraudio/wo...s.asp?Q=1&I=42
and oh.. 12volt agree's with me...
http://www.the12volt.com/caraudio/wo...s.asp?Q=1&I=42
Bad example!!! That's for a mono amp!!!!
Check No. 1 out, exactly as I suggested, and phased as I suggested:
http://colomar.com/Shavano/dvc_spkr_wiring.html
And you got your engineering degree in what???? I remember having to help you with powering up LEDs!!!
Last edited by Takeda; 02-23-2009 at 05:29 AM.
#17
WTF? Where in the hell did you see me even mention frequency? Are you just looking up web pages and posting the stuff you read?
#18
Whats all this talk about AC? I thought subs and speakers ran off of DC?? lol jk!
I called the manufacturer and the guy told me to wire each coil to a seperate channel on the amp. This is best way to get the most sound and performance out of your sub. If I put the coils in series, the 8 ohm load will only perform at half the power. I also went to a tech high school for electronics, and now Im in college taking some electronics courses for my IT major. And it does make sense. Simple resistor circuits, resistance equals force against current. More resistance = less current = less power. I just didn't know if it was safe it seams weird wiring one sub to two different channels.
Colomar suggested using a cross over with subs wired this way, but I won't need one right?
I called the manufacturer and the guy told me to wire each coil to a seperate channel on the amp. This is best way to get the most sound and performance out of your sub. If I put the coils in series, the 8 ohm load will only perform at half the power. I also went to a tech high school for electronics, and now Im in college taking some electronics courses for my IT major. And it does make sense. Simple resistor circuits, resistance equals force against current. More resistance = less current = less power. I just didn't know if it was safe it seams weird wiring one sub to two different channels.
Colomar suggested using a cross over with subs wired this way, but I won't need one right?
#19
Whats all this talk about AC? I thought subs and speakers ran off of DC?? lol jk!
I called the manufacturer and the guy told me to wire each coil to a seperate channel on the amp. This is best way to get the most sound and performance out of your sub. If I put the coils in series, the 8 ohm load will only perform at half the power. I also went to a tech high school for electronics, and now Im in college taking some electronics courses for my IT major. And it does make sense. Simple resistor circuits, resistance equals force against current. More resistance = less current = less power. I just didn't know if it was safe it seams weird wiring one sub to two different channels.
Colomar suggested using a cross over with subs wired this way, but I won't need one right?
I called the manufacturer and the guy told me to wire each coil to a seperate channel on the amp. This is best way to get the most sound and performance out of your sub. If I put the coils in series, the 8 ohm load will only perform at half the power. I also went to a tech high school for electronics, and now Im in college taking some electronics courses for my IT major. And it does make sense. Simple resistor circuits, resistance equals force against current. More resistance = less current = less power. I just didn't know if it was safe it seams weird wiring one sub to two different channels.
Colomar suggested using a cross over with subs wired this way, but I won't need one right?
You are correct about the power....... P = V*V/R
Keep in mind that each VC in a dual VC sub are electrically isolated.
#20
I was joking about speakers being dc by the way.
I put together my box with liquid nail caulk stuff. I didnt make the box from scratch, just took my dual box cut it down about 3/4 of its original size, took out the separating board inside to give myself a smaller box with more air space (for one sub). I blocked up the half hole from the other sub with 3/4 mdf board, and the side with the existing board. So now its connected with liquid nail. What size screws do i put in and do i pre drill first? How do I got about making the physical connections without splitting the wood?
I put together my box with liquid nail caulk stuff. I didnt make the box from scratch, just took my dual box cut it down about 3/4 of its original size, took out the separating board inside to give myself a smaller box with more air space (for one sub). I blocked up the half hole from the other sub with 3/4 mdf board, and the side with the existing board. So now its connected with liquid nail. What size screws do i put in and do i pre drill first? How do I got about making the physical connections without splitting the wood?
#21
This is best way to get the most sound and performance out of your sub. If I put the coils in series, the 8 ohm load will only perform at half the power. I also went to a tech high school for electronics, and now Im in college taking some electronics courses for my IT major. And it does make sense. Simple resistor circuits, resistance equals force against current. More resistance = less current = less power. I just didn't know if it was safe it seams weird wiring one sub to two different channels.
Colomar suggested using a cross over with subs wired this way, but I won't need one right?
Colomar suggested using a cross over with subs wired this way, but I won't need one right?
An amp which can handle 4ohm bridged can handle 2ohm stereo.
Say an amp can do 50wx2 @ 2ohm, it can do 100w bridged at 4ohm.
If you put each channel on a 4ohm load your total power output will be 50w. 25w x 2. If you put a single 8ohm load bridged on the amp, total power output will be 50w.
The thing is, power limitations are usually current related (with maximum voltage being constant). The amp will be less efficient and (depending on the design of the amp) possibly put out less power at the lower load. However, in either case the differences will most likely be undetectable by ear.
Going back to impedance rise. The biggest cause of impedance rise aside from induction vs frequency is heat. Heat raises the resistance of the coils which in turn adds a constant amount of impedance. So if your impedance rise from heat is 1ohm that is a 25% rise on a 4ohm load but only a 12.5% rise on an 8ohm load.
:)
#22
The manufacturer is, in general, incorrect.
An amp which can handle 4ohm bridged can handle 2ohm stereo.
Say an amp can do 50wx2 @ 2ohm, it can do 100w bridged at 4ohm.
If you put each channel on a 4ohm load your total power output will be 50w. 25w x 2. If you put a single 8ohm load bridged on the amp, total power output will be 50w.
The thing is, power limitations are usually current related (with maximum voltage being constant). The amp will be less efficient and (depending on the design of the amp) possibly put out less power at the lower load. However, in either case the differences will most likely be undetectable by ear.
Going back to impedance rise. The biggest cause of impedance rise aside from induction vs frequency is heat. Heat raises the resistance of the coils which in turn adds a constant amount of impedance. So if your impedance rise from heat is 1ohm that is a 25% rise on a 4ohm load but only a 12.5% rise on an 8ohm load.
:)
An amp which can handle 4ohm bridged can handle 2ohm stereo.
Say an amp can do 50wx2 @ 2ohm, it can do 100w bridged at 4ohm.
If you put each channel on a 4ohm load your total power output will be 50w. 25w x 2. If you put a single 8ohm load bridged on the amp, total power output will be 50w.
The thing is, power limitations are usually current related (with maximum voltage being constant). The amp will be less efficient and (depending on the design of the amp) possibly put out less power at the lower load. However, in either case the differences will most likely be undetectable by ear.
Going back to impedance rise. The biggest cause of impedance rise aside from induction vs frequency is heat. Heat raises the resistance of the coils which in turn adds a constant amount of impedance. So if your impedance rise from heat is 1ohm that is a 25% rise on a 4ohm load but only a 12.5% rise on an 8ohm load.
:)
The minimum impedance an amp can drive in stereo or mono (bridged) depends on the amplifier. Some amps can handle a lower impedance in stereo mode, while others can handle a lower impedance in mono (bridged) mode.
As previously posted, the drive voltage will be the same in stereo or mono (bridged) mode, while the current drive is increased in mono (bridged) mode.
With the bridged specs on his amp, the RMS power @ a 4 ohm load is 560WATTS, which will be 280WATTS with a 8 ohm load, while it will deliver 220WATTS * 2 with a 4 ohm load in stereo mode. So, with each VC wired to separate channels on his amp, he will get 160WATTS more power, than the voice coils wired in series giving a total of 8 ohms in bridged mode.
And even with a 1 ohm increase in 4 ohm mode due to heating, this won't come close to the power being lost with 8 ohms.
Last edited by Takeda; 02-23-2009 at 03:35 PM.
#23
Alright so we got the wiring down. Im all set with that. Now here's my modified box:
The two pieces I added are held together by a crap load of liquid nail caulk, I did it last night and the stuff still isnt dry. Now, what do I do, get some small wood screws and put those in?
For cosmetics...I am going to cut off the wood hanging over that was a mistake. But, can I paint over the carpet with spray paint? I was thinking about painting the box red, the color of my truck. Will this work? Or should I tear off the carpet and paint it? Or leave the carpet and just have that one spot where I patched up the hole without carpet? That is the side that will face towards the rear wall anyways.
The two pieces I added are held together by a crap load of liquid nail caulk, I did it last night and the stuff still isnt dry. Now, what do I do, get some small wood screws and put those in?
For cosmetics...I am going to cut off the wood hanging over that was a mistake. But, can I paint over the carpet with spray paint? I was thinking about painting the box red, the color of my truck. Will this work? Or should I tear off the carpet and paint it? Or leave the carpet and just have that one spot where I patched up the hole without carpet? That is the side that will face towards the rear wall anyways.
#25
The minimum impedance an amp can drive in stereo or mono (bridged) depends on the amplifier. Some amps can handle a lower impedance in stereo mode, while others can handle a lower impedance in mono (bridged) mode.
As previously posted, the drive voltage will be the same in stereo or mono (bridged) mode, while the current drive is increased in mono (bridged) mode.
With the bridged specs on his amp, the RMS power @ a 4 ohm load is 560WATTS, which will be 280WATTS with a 8 ohm load, while it will deliver 220WATTS * 2 with a 4 ohm load in stereo mode. So, with each VC wired to separate channels on his amp, he will get 160WATTS more power, than the voice coils wired in series giving a total of 8 ohms in bridged mode.
And even with a 1 ohm increase in 4 ohm mode due to heating, this won't come close to the power being lost with 8 ohms.
As previously posted, the drive voltage will be the same in stereo or mono (bridged) mode, while the current drive is increased in mono (bridged) mode.
With the bridged specs on his amp, the RMS power @ a 4 ohm load is 560WATTS, which will be 280WATTS with a 8 ohm load, while it will deliver 220WATTS * 2 with a 4 ohm load in stereo mode. So, with each VC wired to separate channels on his amp, he will get 160WATTS more power, than the voice coils wired in series giving a total of 8 ohms in bridged mode.
And even with a 1 ohm increase in 4 ohm mode due to heating, this won't come close to the power being lost with 8 ohms.
For someone who likes to lecture people about electronics, you sure have minimal brand recognition.
Case in point, this little beauty of mine. These are real world, rested power outputs.
USamps USA-100:
2 x 52W @ 4 ohms
2 x 105W @ 2 ohms
2 x 158W @ 1 ohm
1 x 315W @ 2 ohms bridged
at 4ohm bridged it makes about 200w.
Bridging amps can work like this (higher loads have proportionally more power than you would think) but they can not work the way PA has stated in their specs except under certain, highly regulated conditions, and AFAIK PA does not use a regulated power supply because if they did, they may as well have the same power ouput 2-8ohm.
Last edited by CBFranger; 02-24-2009 at 08:48 AM.