Engine & Drivetrain Ford Ranger engine and drivetrain parts, i.e. radiators, driveshafts, knuckles, brakes.

For Sale: Hurst shifter (CO)

  #1  
Old 03-03-2012
Member
Thread Starter
Join Date: Mar 2011
Location: Colo. Spgs., Colorado
Posts: 29
Hurst shifter (CO)

Was installed in my 04 for about a month, before removing due to leaking issues. I have been really busy with work and getting ready for college next year and just haven't had much time to address the problem. I could also use the money for college.

I am asking $170, I bought it for $220 on summit. I can meet up to 20 miles from Colorado Springs. I am also willing to ship as long as a means of payment is discussed.

The boot has already been cut, to fit beneath cup holders. Attached picture shows everything that will be sold.
 
Attached Thumbnails Hurst shifter (CO)-221-resized.jpg  

Last edited by EStrauch12; 03-04-2012 at 08:05 AM.
  #2  
Old 03-05-2012
hurley's Avatar
Member
iTrader: (3)
Join Date: Dec 2010
Location: West Belmar NJ
Posts: 1,491
I wish I had the money for this
 
  #3  
Old 03-05-2012
Member
Join Date: Oct 2011
Location: Cranberry Township, PA
Posts: 35
Originally Posted by EStrauch12 View Post
Was installed in my 04 for about a month, before removing due to leaking issues. I have been really busy with work and getting ready for college next year and just haven't had much time to address the problem. I could also use the money for college.

I am asking $170, I bought it for $220 on summit. I can meet up to 20 miles from Colorado Springs. I am also willing to ship as long as a means of payment is discussed.

The boot has already been cut, to fit beneath cup holders. Attached picture shows everything that will be sold.
I have a really big favor to ask if you would not mind? I have a complete shifter EXCEPT for the mounting plate that bolts to the transmission. It is in the center of your photo. I would like to make one, but up till now I have been unable to get the proper dimensions. If it is not to much trouble could you measure your plate for me. I have uploaded a photo to show what dimensions I need. Thank you VERY MUCH!
 
Attached Thumbnails Hurst shifter (CO)-measurements.jpg  
  #4  
Old 03-05-2012
Member
Thread Starter
Join Date: Mar 2011
Location: Colo. Spgs., Colorado
Posts: 29
Originally Posted by idigchoppers View Post
I have a really big favor to ask if you would not mind? I have a complete shifter EXCEPT for the mounting plate that bolts to the transmission. It is in the center of your photo. I would like to make one, but up till now I have been unable to get the proper dimensions. If it is not to much trouble could you measure your plate for me. I have uploaded a photo to show what dimensions I need. Thank you VERY MUCH!
I could do that do you. I will have it posted by the end of the weekend I that's okay, I am busy with school this week. Also I don't have a dial caliper so my measurements may be off very slighty. But otherwise I have no problem doing that for you.
 
  #5  
Old 03-05-2012
Member
Join Date: Oct 2011
Location: Cranberry Township, PA
Posts: 35
Originally Posted by EStrauch12 View Post
I could do that do you. I will have it posted by the end of the weekend I that's okay, I am busy with school this week. Also I don't have a dial caliper so my measurements may be off very slighty. But otherwise I have no problem doing that for you.
THANK YOU very much, that is very nice of you! I am forever greatful!
 
  #6  
Old 03-05-2012
EnCoDeD's Avatar
Member
Join Date: Mar 2011
Location: Chatham, Ontario
Posts: 27
I have the exact same problem, got the shifter without a mounting plate and Hurst will not sell just the plate. I wish you was closer I would let you use my digital calliper. Hope to get some measurements and get a shop to mill it out for me out of 6061 Aluminum.
 
  #7  
Old 03-10-2012
Member
Thread Starter
Join Date: Mar 2011
Location: Colo. Spgs., Colorado
Posts: 29
Hurst Mounting Plate DImensions:
TOP VIEW
A: 7.5 cm 3 in
B: 3.5 cm 1 3/8 in

BOTTOM VIEW
B 3.5 cm 1 3/8 in (same measurement as top view B)
C 4 cm 1 9/16 in

SIDE VIEW
D .6 cm 1/4 in
E 1 cm 3/8 in

I took these measurements as precisely as possible with out the use of a digital caliper. Let me know if you have any further questions. Good luck!
 
  #8  
Old 03-10-2012
Member
Join Date: Oct 2011
Location: Cranberry Township, PA
Posts: 35
Originally Posted by EStrauch12 View Post
Hurst Mounting Plate DImensions:
TOP VIEW
A: 7.5 cm 3 in
B: 3.5 cm 1 3/8 in

BOTTOM VIEW
B 3.5 cm 1 3/8 in (same measurement as top view B)
C 4 cm 1 9/16 in

SIDE VIEW
D .6 cm 1/4 in
E 1 cm 3/8 in

I took these measurements as precisely as possible with out the use of a digital caliper. Let me know if you have any further questions. Good luck!
Wow, thank you VERY MUCH. I really appreciate the help!
Did you sell your shifter yet? You shouldn't have any problem selling it.
They are quite popular.
 
  #9  
Old 03-19-2012
2004xlmiller's Avatar
Member
iTrader: (5)
Join Date: Sep 2010
Location: Sac, CA
Posts: 1,601
i might be interested.. lemme think about it.
 
  #10  
Old 03-20-2012
2004xlmiller's Avatar
Member
iTrader: (5)
Join Date: Sep 2010
Location: Sac, CA
Posts: 1,601
pm sent
 
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
rngprerunner
Engine & Drivetrain
5
4 Weeks Ago 07:43 PM
bmwysocki
Drivetrain Tech
13
05-03-2006 05:06 PM
Zero
Drivetrain Tech
30
12-28-2005 05:33 PM
rngprerunner
Engine & Drivetrain
0
06-27-2005 09:29 PM


Thread Tools
Search this Thread
Quick Reply: For Sale: Hurst shifter (CO)


Contact Us - Sitemap - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.