Vent Visors
#1
#2
I got ventshades. They where on the truck when I bought it, but almost everyone sells them. They are the in channel ones too, there are other ones that use 3M tape, I like the low profile ones tho. It's nice because i think they cut down on wind noise when the window cracked since it's pushing it away, It's the coolest to use in the rain.
I usually crack my windows in parking lots by maybe 1cm (eyeballing it) max to let some heat out in the summer, and while im working.
I usually crack my windows in parking lots by maybe 1cm (eyeballing it) max to let some heat out in the summer, and while im working.
#3
personally i like my LUND the best that i have seen in person so far the injection molding looks the cleanest. it installs with 3M tap on the INSIDE of the channel. really easy to do. pull of the tap stick it up there with the window rolled down. then roll up the window. apply pressure to the gasket and seal the 3M tape and VOLA done....move on with life
#5
I've got the AVS snap in kind. No tape, they just fit in the window chanel. They are allright I guess, the fit leaves a little to be desired around the top rear of the window. I wound up doing a little trimming on them and they are better than they were. The only really good thing about them is you can put them on and off whenever you want, it only takes a second.
#10
#12
I was told by a guy at schucks today that the in channle ones wear out over time and dont stay up, and that people keep coming back to replace them. makes sense, but i dont trust tape to hold it on on the highwayeither, last thing i want it to see it fly off completely...so im going to go in tomarrow and order the in channel ones
#15
#16
Ya know I have almost ordered them about 3 times but for some reason i never did. I was going to get the ones that go in the channel no tape or drill.
"EGR In-Channel Window Visors: Thin tapered lip slides into your vehicle's window channel for a smooth, low-profile look with no drilling and no exterior tape. Available in smoked finish. "
http://www.stylinconcepts.com/parts....q=vent%20visor
"EGR In-Channel Window Visors: Thin tapered lip slides into your vehicle's window channel for a smooth, low-profile look with no drilling and no exterior tape. Available in smoked finish. "
http://www.stylinconcepts.com/parts....q=vent%20visor
#18
Originally Posted by Ranger1
Ya know I have almost ordered them about 3 times but for some reason i never did. I was going to get the ones that go in the channel no tape or drill.
"EGR In-Channel Window Visors: Thin tapered lip slides into your vehicle's window channel for a smooth, low-profile look with no drilling and no exterior tape. Available in smoked finish. "
http://www.stylinconcepts.com/parts....q=vent%20visor
"EGR In-Channel Window Visors: Thin tapered lip slides into your vehicle's window channel for a smooth, low-profile look with no drilling and no exterior tape. Available in smoked finish. "
http://www.stylinconcepts.com/parts....q=vent%20visor
#19
#20
#21
Originally Posted by speedranger
I was told by a guy at schucks today that the in channle ones wear out over time and dont stay up, and that people keep coming back to replace them. makes sense, but i dont trust tape to hold it on on the highwayeither, last thing i want it to see it fly off completely...so im going to go in tomarrow and order the in channel ones
#22
Member
iTrader: (3)
Join Date: May 2005
Location: MI
Posts: 3,200
Likes: 0
Received 0 Likes
on
0 Posts
I HATE my vent visors....It sounds like i have a freaking window cracked every time i drive down the road....Its SO annoying. They are noisey because air gets trapped in the pocket area where plastic ends by the top of the window...I am going to try and trim the corner, and if that dont work im ripping them out.
#24
Originally Posted by 01xltranger4x4
I HATE my vent visors....It sounds like i have a freaking window cracked every time i drive down the road....Its SO annoying. They are noisey because air gets trapped in the pocket area where plastic ends by the top of the window...I am going to try and trim the corner, and if that dont work im ripping them out.