Bed swap, who's done it.
#1
05-29-2008
Join Date: May 2008
Location: St. Clair Shores, MI
Posts: 11
Likes: 0
Received 0 Likes
on
0 Posts
Bed swap, who's done it.
I just picked up a 99 XLT and the bed is scratched pretty bad and has some decent sized dents in it. I'm thinking it would just be easier to swap a newer bed on it and then paint it to match versus doing the body work.
Has anyone done this? What was your experience with it? It seems pretty cut and dry to me. Disconnect filler neck at fuel door. Un-bolt bed from frame and remove tail gate. Then lift off and replace.
Has anyone done this? What was your experience with it? It seems pretty cut and dry to me. Disconnect filler neck at fuel door. Un-bolt bed from frame and remove tail gate. Then lift off and replace.
#2
05-29-2008
Join Date: May 2005
Location: Livonia, Mi
Posts: 12
Likes: 0
Received 0 Likes
on
0 Posts
its simple.
the only thing you left out is the tail light wiring harness.
check on www.car-part.com for a bed, anything 93-08 should fit.
if you have a 6ft bed you can put on a flare side or a style side.
the only thing you left out is the tail light wiring harness.
check on www.car-part.com for a bed, anything 93-08 should fit.
if you have a 6ft bed you can put on a flare side or a style side.
#5
05-29-2008
So did I, on a 93.
Get a 40+" breaker bar and a T55 driver.
Crawl underneath and SOAK the visible threads with PB Blaster or equivalent (not WD40).
Be prepared for a sore back the next day, if you aren't used to pulling in excess of 150 ft/lbs over and over again. You'll want something to rest your knees on too.
An Impact gun with 120 psi couldn't TOUCH those bed bolts. Even after I turned them out partway, the impact wouldn't do it and they don't get any easier as they come out further.
There is a disconnection point for the tail lights, right about at the center of the tailgate, so look for that. You also want a strong friend to help lift it off AFTER you remove the tailgate.
Get a 40+" breaker bar and a T55 driver.
Crawl underneath and SOAK the visible threads with PB Blaster or equivalent (not WD40).
Be prepared for a sore back the next day, if you aren't used to pulling in excess of 150 ft/lbs over and over again. You'll want something to rest your knees on too.
An Impact gun with 120 psi couldn't TOUCH those bed bolts. Even after I turned them out partway, the impact wouldn't do it and they don't get any easier as they come out further.
There is a disconnection point for the tail lights, right about at the center of the tailgate, so look for that. You also want a strong friend to help lift it off AFTER you remove the tailgate.
#7
05-29-2008
Join Date: May 2005
Location: Livonia, Mi
Posts: 12
Likes: 0
Received 0 Likes
on
0 Posts
go to the website i posted, it will show you what your local junkyards have.
clean beds go for $300-$1000+ depending on how lucky you are.
when you buy one make sure you look at the underside of it, sometimes they look find from the outside but they are rotted where you can't normally see.
clean beds go for $300-$1000+ depending on how lucky you are.
when you buy one make sure you look at the underside of it, sometimes they look find from the outside but they are rotted where you can't normally see.
#9
05-29-2008
Join Date: May 2008
Location: St. Clair Shores, MI
Posts: 11
Likes: 0
Received 0 Likes
on
0 Posts
Thread
Thread Starter
Forum
Replies
Last Post
Want to Trade: 2001 bed swap ( 6ft std bed for stepside)
fx4wannabe
OLD - Interior, Exterior, Electrical, & Misc.
6
08-06-2010 08:09 AM
