what kind of power am i looking at?
#1
08-19-2006
Join Date: Feb 2006
Location: Garland, Texas
Posts: 20
Likes: 0
Received 0 Likes
on
0 Posts
what kind of power am i looking at?
i just bought a fully built turbo 2.3L motor from a friend...wat kinda power am i looking at making at maybe 18 psi and also what program can i use or who can i go to to get tuned?
here are the specs:
2.3 Turbo engine block (From a 88' turbo coupe)
bored .30 over
T3 Turbo .63AR
new forged pistons
E6 Exhaust manifold
speed pro Chrommoly rings
new rod & main bearings
new oil pump
new walbro 255lph fuel pump
new distributor cap & rotor
new water pump
new idler pulley
new thermostat
new fomo co. head bolts
Big MAF
lb2 ecu
2 88' TC intercoolers
S.S. Braided oil feed line & original T3 oil line
more specific specs:
Head:
Oversized valves, slightly ported.
A237 cam
adj cam sprocket
The pistons:
speed pro L2500F .75mm over (since its bored over .030)
Size point 1.90 from top of head
min. clearance .0024
Bore range 3.8091-3.8101
Skirt size 3.80635 +/- .00025 inches
Compression ratio:
Is the same as the original motor, which I believes comes too around 8.5:1 or so
here are the specs:
2.3 Turbo engine block (From a 88' turbo coupe)
bored .30 over
T3 Turbo .63AR
new forged pistons
E6 Exhaust manifold
speed pro Chrommoly rings
new rod & main bearings
new oil pump
new walbro 255lph fuel pump
new distributor cap & rotor
new water pump
new idler pulley
new thermostat
new fomo co. head bolts
Big MAF
lb2 ecu
2 88' TC intercoolers
S.S. Braided oil feed line & original T3 oil line
more specific specs:
Head:
Oversized valves, slightly ported.
A237 cam
adj cam sprocket
The pistons:
speed pro L2500F .75mm over (since its bored over .030)
Size point 1.90 from top of head
min. clearance .0024
Bore range 3.8091-3.8101
Skirt size 3.80635 +/- .00025 inches
Compression ratio:
Is the same as the original motor, which I believes comes too around 8.5:1 or so
Last edited by ZoNe5; 08-19-2006 at 02:43 PM. Reason: more questions
#6
08-19-2006
Join Date: Feb 2006
Location: Garland, Texas
Posts: 20
Likes: 0
Received 0 Likes
on
0 Posts
#9
08-20-2006
Unregistered User
Posts: n/a
Originally Posted by ZoNe5
ok im ranger retarted...i dont know too much about these trucks...at first i was planning on selling it but after i found this motor it arose some interest in me...EMTec3...where would i go about getting this and im going for a front mount so those intercoolers arent going to be used
Google search ' Electro Motive Tec3 ' and links will pop up for the ECU. Its the best out there, works with ANY Engine and is HIGHLY programmable. Its NOT cheap.
#10
08-22-2006
Join Date: Feb 2006
Location: Garland, Texas
Posts: 20
Likes: 0
Received 0 Likes
on
0 Posts
#12
08-29-2006
Join Date: Aug 2006
Location: Nawlins
Posts: 401
Likes: 0
Received 0 Likes
on
0 Posts
Thread
Thread Starter
Forum
Replies
Last Post
WowMike2001
General Technical & Electrical
13
08-16-2009 07:41 AM
