svt 4.6 supercharged engine - Page 2 - Ranger-Forums - The Ultimate Ford Ranger Resource

Forced Induction & N20 Tech General discussion of forced induction and nitrous for the Ford Ranger.

svt 4.6 supercharged engine

  #26  
Old 11-04-2011
BLK02's Avatar
Member
iTrader: (2)
Join Date: Dec 2007
Location: BC
Posts: 1,350
Originally Posted by 04RangerDave View Post
if its a 2.2 or 2.8 kb there is no way its putting down over 9xx. Even with a 150 shot and stock IRS that's not broken yet is very hard to believe. Why doesn't he join RF and ask questions not his friend?
The only way a kb cobra gets near 1000hp is with a 300 shot of nitrous :p, regardless it will fit but will we see this actually happen? My money is on no
 
  #27  
Old 11-17-2011
angus-'s Avatar
Member
Join Date: Nov 2011
Location: Wa
Posts: 44
Originally Posted by spadanko View Post
#55 injectors with 900+hp.... somethin doesnt add up even close
Someone mixed up his dyno sheet with a 2JZ one...

And he must have meant 155lb. injectors


 
  #28  
Old 11-17-2011
BisketFx4's Avatar
Member
Join Date: Mar 2009
Location: Chattahoochee, Fl
Posts: 159
I dont know if yall have seen this yet. http://www.spike.com/full-episodes/7...eason-2-ep-205
 
  #29  
Old 11-29-2011
spoolinranger's Avatar
Member
Join Date: Jun 2011
Location: oneida,tn
Posts: 3
I'm sure the mammoth kenne belle can put those numbers out, but 55lb injectors is a fact not happening.
 
  #30  
Old 11-29-2011
Member
Thread Starter
Join Date: Jun 2011
Location: lakeland, florida
Posts: 220
that dyno was on race gas and some of them specs are from his old setup
 
  #31  
Old 11-30-2011
Downey's Avatar
RF Veteran
iTrader: (1)
Join Date: Oct 2007
Location: Muncy, PA
Posts: 8,470
so answer your question yes you can put the motor in. it will take major work its not like swapping in a 5.0. if you have watched trucks on spike you would see that they swapped in a super charged 4.6 into a ranger
 
  #32  
Old 03-05-2012
mikey7o2's Avatar
Member
Join Date: Mar 2012
Location: las vegas nv
Posts: 60
I think your friend should give it a shot ! I would love to see a motor like that in a ranger (even if in my opinion its running closer to 550hp - 600hp)
 
  #33  
Old 07-15-2012
Member
Join Date: Jul 2012
Location: Eagan, MN
Posts: 14
Tell him to just sell the motor. I'm pretty big in the mustang scene and people will pay ludicrous amounts of money for a terminator swap. Plus there's no way in hell he's putting down over 900 HP on a kenne bell with 55# injectors. Maybe that was supposed to be flywheel HP?! Either way, I'd tell him to post that stuff on moddedmustangs.com, svtperformance.com, or corral.net.
 
  #34  
Old 07-18-2012
WildcatRange's Avatar
Member
Join Date: Jul 2011
Location: Sandy Or
Posts: 122
My buddy supercharged his 4.0 V6 for about 1500, that's all I know about supercharged trucks.
 
  #35  
Old 07-20-2012
MudSlanger's Avatar
Member
iTrader: (4)
Join Date: Jun 2007
Location: Phoenix, AZ
Posts: 1,462
Originally Posted by bfd's_ranger View Post
Sooooo you want a 900hp lawn mower?
LMFAO I was thinking the same thing.. Also I need to get in the lawn service. Sounds like they are paying well if he has a 900HP mustang cobra
 
  #36  
Old 07-20-2012
BLK02's Avatar
Member
iTrader: (2)
Join Date: Dec 2007
Location: BC
Posts: 1,350
You can buy a mint low mile kb cobra for 25k.
 
  #37  
Old 07-20-2012
morris's Avatar
RF Veteran
iTrader: (5)
Join Date: Feb 2008
Location: South Detroit.
Posts: 7,837
So I see we're still waiting to see this beast?
 
  #38  
Old 07-20-2012
mac's Avatar
mac
mac is offline
Member
Join Date: Sep 2010
Location: new jersey
Posts: 319
surprise.
 
  #39  
Old 07-20-2012
cdawall's Avatar
Member
Join Date: Dec 2010
Location: EAFB, Sd
Posts: 209
Now that all the BS is over I want to point out there are several 5.4L DOHC and 4.6L DOHC swaps floating around. It will fit without a doubt. It will not require major frame modification on a 2WD, but it will require tranny tunnel work and he needs to ditch the 28 spline 8.8/7.5" for a 31 spline 8.8" or 9". This swap will require some work its a very wide motor in a rather narrow bay. However the aviators have them stock so it should fit.
 
  #40  
Old 03-22-2013
boyd_835's Avatar
Member
Join Date: Jan 2011
Location: lake tapps, wa
Posts: 523
900hp is possible but not with the set up explained thats a 500-650hp setup ive had a few mustangs in the past along with buddies that have built 900+hp ones but that was with gt40 heads, gt40 intake manifold, and one giant turbo at like 27lbs
 
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
93MVSplash
General Ford Ranger Discussion
26
09-09-2008 09:30 PM
vic
2.9L & 3.0L V6 Tech
20
10-10-2006 09:27 PM
Werty
4.0L OHV & SOHC V6 Tech
19
04-12-2006 01:07 PM
EdGe_wannabe
General Ford Ranger Discussion
22
11-17-2005 03:59 PM
gbgary
Forced Induction & N20 Tech
36
10-12-2005 08:13 AM


Thread Tools
Search this Thread
Quick Reply: svt 4.6 supercharged engine


Contact Us Sitemap Advertising Cookie Policy Privacy Statement Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.