Power Windows, Part 3 (Install Phase 2, Strange Stuff. Not 56K friendly!)
(See last post here)
Well everyone, got my power windows installed this weekend. Here's a pic of my truck after I was done: http://img118.imageshack.us/img118/2...uckfirewb4.jpg Just kidding. The installation went will, with a few minor roadblocks. The hardest part of this installation was figuring out the bolt pattern for the new regulators. Once that was figured out, it really was just bolt-on-and-go. I ended up having my little brother hold the windows. I tried the masking tape approach, but ended up having to coordinate moving the window and threading the regulator at the same time. Not easy. http://img262.imageshack.us/img262/6172/tapecj9.jpg Once it was in, I plugged in the control and tested it. It worked! Then I discovered a slight flaw in my setup. When the window was fully down, I noticed the motors worked harder and I actually blew the 10A fuse for them. Turns out the rivets that hold the window to the track were rubbing on the new arm. So, I had to drill down one rivet on each door so it would clear. Talk about nerve racking! :Eyecrazy: Anyone else have this problem????? The undrilled rivet (towards rear of truck): http://img251.imageshack.us/img251/1...redrillmh3.jpg And what I had to do to the forward rivets to get them to clear the arms... http://img260.imageshack.us/img260/1...stdrillhy4.jpg The whole thing took the better part of an afternoon, but the end result was well worth it. Now I just need to tidey up the wiring, grease the window tracks and figure out what to do about the dust panels. Anyone know where I can get replacements? The old ones have long lost their sticky. |
sweet! i bet you like it now don't ya...
|
Awesome job. The A1 setup didn't have the rivet problem because the plate used to mount to in the inside of the door had studs made into that plate that stuck out towards the inside of the truck. You just had to put the nuts on it, so it wasn't to the inside of the door, it was towards the outside.
|
Originally Posted by 05RangerXLT
Awesome job. The A1 setup didn't have the rivet problem because the plate used to mount to in the inside of the door had studs made into that plate that stuck out towards the inside of the truck. You just had to put the nuts on it, so it wasn't to the inside of the door, it was towards the outside.
|
It was an A1 kit but you had rivets?
|
My A1 kit required me to drill out the rivets holding the stock manual regulator. Then I used holes already in the door frame that studs came through so I could hold the regulator plate assembly firmly to the door. There were no rivets sticking out in the way of the arm. That's what I didn't follow.
|
Originally Posted by 05RangerXLT
My A1 kit required me to drill out the rivets holding the stock manual regulator. Then I used holes already in the door frame that studs came through so I could hold the regulator plate assembly firmly to the door. There were no rivets sticking out in the way of the arm. That's what I didn't follow.
|
nice i wish i had power windows
|
Still looking for suggestions on replacing the dust covers.
Also, I've determined that I need to look into limiting moter actuation. Can anyone recommend some current limiting switches to stop the windows when they are all the way up or down? |
hmmm...... f-150 on fire
|
Originally Posted by heaton84
Still looking for suggestions on replacing the dust covers.
Also, I've determined that I need to look into limiting moter actuation. Can anyone recommend some current limiting switches to stop the windows when they are all the way up or down? |
:bump:
Anyone? Someone has to have encountered this before... |
All times are GMT -6. The time now is 04:05 AM. |
© 2024 MH Sub I, LLC dba Internet Brands