to those of you with a body lift and a manual transmission...... - Page 2 - Ranger-Forums - The Ultimate Ford Ranger Resource


General Ford Ranger Discussion General discussion of the Ford Ranger that does not fit in any other sub-forum.

Reply
 
LinkBack Thread Tools Search this Thread
  #26  
Old 12-04-2007
DangaRanger99's Avatar
Member
 
Join Date: Mar 2006
Location: Farmington, NH
Posts: 1,209
Maurice you could do a hurst with Wayne's shifter lifter
Reply With Quote
  #27  
Old 12-04-2007
lifted97ranger's Avatar
Member
Thread Starter
 
Join Date: Nov 2005
Location: Charlestown, IN
Posts: 1
Quote:
Originally Posted by RazorsEDGE
That will be another one of those elusive parts. I turned to my dealer about the part, but they insisted that it never existed and that the only RCM cover was the twin cup holder console. I PM'd Bob about the part for help locating it and he gave his to me. I'd probably still be looking for some of the LVL II parts iif it wasn't for him.
anyway you could pull it off and get the part #'s off it?


Quote:
Originally Posted by DangaRanger99
iMaurice you could do a hurst with Wayne's shifter lifter
i dont want a Hurst shifter......
Reply With Quote
  #28  
Old 12-04-2007
99ranger4x4's Avatar
RF Veteran
iTrader: (3)
 
Join Date: Jun 2006
Location: Austin, TX
Posts: 12,198
hm, i could use one of them too before i destroy it lol (the cover)
Reply With Quote
  #29  
Old 12-04-2007
RazorsEDGE's Avatar
There's no lifeguard in the gene pool
iTrader: (4)
 
Join Date: Aug 2006
Location: New Mexico
Posts: 7,501
Quote:
Originally Posted by lifted97ranger
anyway you could pull it off and get the part #'s off it?



I could pull it off and see if the part # is on it. I never even thought to look before I put it in.
Reply With Quote
  #30  
Old 12-05-2007
RazorsEDGE's Avatar
There's no lifeguard in the gene pool
iTrader: (4)
 
Join Date: Aug 2006
Location: New Mexico
Posts: 7,501
I pulled the cover today and got the part # from the underside of it, there were three of them stamped on it. I looked on www.fastpartsnetwork.com and the #'s netted no results, but maybe you would have better luck asking a dealer to look it up.

part number:
3L54-13130B24-AAW
2L54-13130B24-AAW
2L54-13130B24-ABW
Reply With Quote
  #31  
Old 12-05-2007
lifted97ranger's Avatar
Member
Thread Starter
 
Join Date: Nov 2005
Location: Charlestown, IN
Posts: 1
thanks man...
Reply With Quote
  #32  
Old 12-05-2007
Lefty04LevelII's Avatar
Member
 
Join Date: Aug 2005
Location: DFW
Posts: 1,447
Quote:
Originally Posted by RazorsEDGE
I pulled the cover today and got the part # from the underside of it, there were three of them stamped on it. I looked on www.fastpartsnetwork.com and the #'s netted no results, but maybe you would have better luck asking a dealer to look it up.

part number:
3L54-13130B24-AAW
2L54-13130B24-AAW
2L54-13130B24-ABW

I can't locate those on http://www.trademotion.com/partlocat...?siteid=213787 either...

I do have an 02 and 03 VIN so I could just call the dealership and see if they could help.
Reply With Quote
  #33  
Old 12-05-2007
lifted97ranger's Avatar
Member
Thread Starter
 
Join Date: Nov 2005
Location: Charlestown, IN
Posts: 1
Chris can you get the part number for the shifter surrond? you have the Level II shifter without the manual t-case don't ya?
Reply With Quote
  #34  
Old 12-05-2007
Lefty04LevelII's Avatar
Member
 
Join Date: Aug 2005
Location: DFW
Posts: 1,447
Quote:
Originally Posted by lifted97ranger
Chris can you get the part number for the shifter surrond? you have the Level II shifter without the manual t-case don't ya?
Yes, I have the double cup holder console (is that what you're talking about) and my factory LII shifter. Or are you talking about the floor plate?

I'll try to get photos tomorrow after work and go from there?

anyone have a good source for aftermarket carpet? Ford wants $350 for 02 or 03 ebony carpet. The hole cut in my carpet for my shifter is just barely too large and I'm trying to keep an OEM look. If I could pay off this blasted CC of mine I'd just put the carpet on it.

EDIT: You know, the old style of twin shifter console and boots wouldn't look too bad either. It would hold me over until I could get the right carpet too.

Last edited by Lefty04LevelII; 12-05-2007 at 10:30 PM.
Reply With Quote
  #35  
Old 12-05-2007
RazorsEDGE's Avatar
There's no lifeguard in the gene pool
iTrader: (4)
 
Join Date: Aug 2006
Location: New Mexico
Posts: 7,501
PM Bob about the carpet. He swapped an Edge rubber floor in when he did his v8 swap. He might still have his factory carpet.
Reply With Quote
  #36  
Old 12-06-2007
lifted97ranger's Avatar
Member
Thread Starter
 
Join Date: Nov 2005
Location: Charlestown, IN
Posts: 1
Quote:
Originally Posted by Lefty04LevelII
Yes, I have the double cup holder console (is that what you're talking about) and my factory LII shifter. Or are you talking about the floor plate?

I'll try to get photos tomorrow after work and go from there?

anyone have a good source for aftermarket carpet? Ford wants $350 for 02 or 03 ebony carpet. The hole cut in my carpet for my shifter is just barely too large and I'm trying to keep an OEM look. If I could pay off this blasted CC of mine I'd just put the carpet on it.

EDIT: You know, the old style of twin shifter console and boots wouldn't look too bad either. It would hold me over until I could get the right carpet too.
Yea the cup holder were the shift boot is at........and the silver trim around the shift boot......I am going to see how much they are new


Summit has new carpet kits for $124
Reply With Quote
Reply

Related Topics
Thread Thread Starter Forum Replies Last Post
For Those With A Manual Transmission... Dynasty General Ford Ranger Discussion 17 05-04-2016 05:24 AM
Questions for those of you with a body lift DangerRanger91 1" & 3" Body Lifts 7 07-06-2011 03:29 PM
2004 Ranger Service Manual, Wiring Manual and Haynes Manual - NC 04blackedge Interior, Exterior, Electrical, & Misc. 1 05-07-2009 05:43 PM
Question for those of you who have done a Body Lift... rngprerunner General Ford Ranger Discussion 6 01-04-2008 01:07 PM
For those of you wanting a CAI, made some vids for you Mike9825 General Ford Ranger Discussion 4 07-21-2006 03:16 PM


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off



All times are GMT -6. The time now is 06:23 AM.


We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.