work i need
I seriously debating getting rid of the truck here is the list let me know what you think. Me nor my work will be performing the work.
- Upper Control Arm assembly - Lower ball joints - Drive side axle - Front wheel bearings - Tie rod ends - Alignment Next 10,000 Miles - Transmission torque converter - Transmission fluid service |
yup keep mods and get a different ranger
|
Trade in on that one you posted about, if your work will let you.
|
Originally Posted by morris
(Post 1885141)
Trade in on that one you posted about, if your work will let you.
read update |
I see.
|
Im just not sure if i should fix it then trade or just trade
|
Well, if your spending the coin to fix it, why trade? Everything that your complaining about would be fixed. If you just trade it away, your getting rid of the problems. However unless you keep quiet about the problems, you might not get a good trade in value for it. get a new one and use it an a dp which is only gonna net you like 5-6k.
|
Originally Posted by morris
(Post 1885152)
Well, if your spending the coin to fix it, why trade? Everything that your complaining about would be fixed. If you just trade it away, your getting rid of the problems. However unless you keep quiet about the problems, you might not get a good trade in value for it. get a new one and use it an a dp which is only gonna net you like 5-6k.
|
If you are using all of your trade as down payment does that mean the truck is payed off?
|
Originally Posted by vista4.0
(Post 1885160)
If you are using all of your trade as down payment does that mean the truck is payed off?
|
ok so why get a new truck. You can get all the front end stuff minus the alignment shipped to your door for under $550 moog ties, balljoints and arms, timken bearings cardone cv. Ya the torque converter sucks but you can do that too. Why wont you or your work perform the work? You can practically do the whole front end in like 4 hours.
|
Originally Posted by vista4.0
(Post 1885163)
ok so why get a new truck. You can get all the front end stuff minus the alignment shipped to your door for under $550 moog ties, balljoints and arms, timken bearings cardone cv. Ya the torque converter sucks but you can do that too. Why wont you or your work perform the work? You can practically do the whole front end in like 4 hours.
|
get another subaru lol
|
I dont know Id probably fix it. Not worth even getting close to a payment. Not to many places that will just let you trade vehicles practically straight up. Although it does help that you work at a dealership.
|
If the truck is paidoff I say fix it and keep it. Whats to say that whatever you buy doesn't have just as many or more problems?
|
Originally Posted by 07rangersport
(Post 1885170)
If the truck is paidoff I say fix it and keep it. Whats to say that whatever you buy doesn't have just as many or more problems?
|
Your asking for trouble when you trade that truck in.
You have no payment now, Correct? all those parts total around 500 - 600 bucks. If your to get a payment, thats about 200 - 300 bucks a month. It isn't worth it IMO. Run it till it dies, than worry about it. |
Originally Posted by StxDangerRanger
(Post 1885177)
Run it till it dies, than worry about it.
Pretty sure those bearings are pretty expensive... you are 4x4 right? Probly close to $500 just for those if you need the whole hub. Nevermind... maybe you are 2wd, haha. Shows how much I pay attention. |
Originally Posted by RLong31
(Post 1885186)
I don't think it's too far off.
Pretty sure those bearings are pretty expensive... you are 4x4 right? Probly close to $500 just for those if you need the whole hub. Nevermind... maybe you are 2wd, haha. Shows how much I pay attention. |
Originally Posted by RLong31
(Post 1885186)
I don't think it's too far off.
Pretty sure those bearings are pretty expensive... you are 4x4 right? Probly close to $500 just for those if you need the whole hub. Nevermind... maybe you are 2wd, haha. Shows how much I pay attention. |
Wirelessly posted
My trucks 4wd. Has problems up the wall. Pedro I Want one but they are expensive I just got back from looking at a gli vr 24v |
Which would be cheaper Torque converter or a 5sp swap?
|
Swap that beds overnight. They will never know. lol
|
Sound advice, brah. ^^
|
Originally Posted by 04RangerDave
(Post 1885165)
yes ik i can do everything. Between work and school i have 2 hours to myself
|
All times are GMT -6. The time now is 10:32 PM. |
© 2024 MH Sub I, LLC dba Internet Brands