Cruise control fuse - Ranger-Forums - The Ultimate Ford Ranger Resource


General Technical & Electrical General technical and electrical discussion for the Ford Ranger that does not fit in any other sub-forum.

Reply
 
LinkBack Thread Tools Search this Thread
  #1  
Old 11-28-2011
Lord Of War's Avatar
Member
Thread Starter
iTrader: (2)
 
Join Date: Jan 2006
Location: Thornton, Colorado
Posts: 4,599
Cruise control fuse

My cruise is not working and I need to find the fuse that controls it. What number/location is the cruise control fuse? I looked in my manual and couldnt find it...

Thanks
-Jake
Reply With Quote
  #2  
Old 11-28-2011
djfllmn's Avatar
Moderator
 
Join Date: Mar 2009
Location: York, PA
Posts: 5,796
check #10 in the pass compartment fuse panel
this is right out of my owners guide
Quote:
Speed Control Servo/Amplifier Assembly,
Generic Electronic Module (GEM), Shift
Lock Actuator, Turn Signals
Reply With Quote
  #3  
Old 11-28-2011
Blhde's Avatar
Member
 
Join Date: Oct 2005
Location: Northern IL
Posts: 2,804
Self-Test Diagnostics

WARNING:
This test is a key on engine off (KOEO) test that is only conducted in park with emergency brake fully engaged.

l Enter self-test diagnostics by depressing the speed control OFF switch while turning the ignition key on, making sure the engine does not start and is not running. The speed control indicator lamp on the instrument panel will flash once to indicate that the speed control module entered the diagnostic mode. Five additional flashes at this point indicate a defective speed control servo. Release the OFF switch.

l Note:
If the ON switch is not pressed within five seconds after entering diagnostic mode, the module times out and the procedure must be started over.

Press the remaining switches in this sequence: ON, RSM (resume), CST (coast) and SET/ACCEL.

l The speed control indicator lamp will flash as each switch is pressed. Press each switch in the sequence immediately after the light goes out for the previous switch.

l Note:
There will be a slight delay when the last button is pressed and the lamp flashes.

A lamp flash with the last button (SET/ACCEL) indicates that the STATIC test passed. If the lamp does not flash with the last button and there are no additional flashes of the lamp, the switch is defective. If the lamp does not flash with the last button, and the additional flashes occur, follow the list below for trouble codes:

— 2 flashes: Brake pedal position (BPP) switch is defective, circuit is defective, or brake pedal is applied; clutch pedal position (CPP) switch is defective, circuit is defective, or clutch pedal is applied.

— 3 flashes: Brake deactivation switch is open or circuit is defective.

— 4 flashes: Vehicle speed signal is out of range or circuit is defective.

l 0.25 seconds after the static test has passed, the speed control servo will carry out a dynamic test automatically by actuating the throttle lever from 1 to 10 mm (.04 to.39 inch) of travel from the idle position. During the dynamic throttle pull, observe throttle movement to witness any binding or sticking of the speed control cable, verify the correct connection of the speed control cable to the throttle lever, and make sure the throttle returns back to the idle position. If incorrect connection or binding or sticking of the speed control is observed, go to the Symptom Chart. If no dynamic pull occurs at the throttle body go to Pinpoint Test F.

l Return the ignition switch to the OFF position and proceed to the Symptom Chart.
Reply With Quote
  #4  
Old 04-20-2012
Member
 
Join Date: Apr 2012
Location: Guatemala
Posts: 1
thank you !!

Test suggested has been performed, that helped me to figure it out what went wrong and resulting as a defective springs at the clutch mechanism. Afterwards everything is now working as it should.
Reply With Quote
  #5  
Old 02-12-2016
Member
 
Join Date: Feb 2016
Location: Philly, PA
Posts: 5
I'd like to resurrect this historic post...I followed the above and got 2 flashes. Now, how would I go about figuring out if my issue is my BPP or CPP?
2004 Ranger XLT 4WD
Reply With Quote
  #6  
Old 04-12-2016
Member
 
Join Date: Feb 2016
Location: Greenbrier, TN
Posts: 4
I performed the KOEO test as detailed in this thread. The On and OFF switch performs as it is supposed to, none of the right side switches do anything. RSM/COAST/SET do not cause a flask or light blink. The switches are new and have been working (cruise quit on highway today), I'm thinking the right side switch is bad, but confused as to why they would all be not working. Ant advice appreciated, THANKS.
Reply With Quote
  #7  
Old 04-13-2016
Member
 
Join Date: Feb 2016
Location: Greenbrier, TN
Posts: 4
I resolved my problem and realized I have fixed this before. The Stoplight or Brake light switch was bad. Once I realized I had no brakes lights I replaced switch and cruise works. I did do the KOEO test detailed in this thread and it does not work on my 99 Ranger, only the left side, ON/OFF switches light cruise light, the right side does nothing. Thanks.
Reply With Quote
Reply

Related Topics
Thread Thread Starter Forum Replies Last Post
Modding cruise control to a non cruise Ranger 2001fordranger General Technical & Electrical 1 07-29-2009 11:58 PM
Fuse Diagram Need to replace Link Port/Data Port Fuse FRXLT General Technical & Electrical 14 05-25-2009 08:48 PM
04 Fuse box, Fuse raiting and location Midnightrider General Technical & Electrical 3 04-11-2008 12:41 PM
Using Cruise Control buttons to control the Volume GVSU Godfather Audio & Video Tech 23 05-29-2005 07:39 PM
Drivers side fuse panel 97 2.3L fuse#2 slot radio_earbug SOHC - 2.3L & 2.5L Lima Engines 4 03-17-2005 11:49 AM


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off



All times are GMT -6. The time now is 03:53 AM.


We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.