OHC wiring problems
#1
OHC wiring problems
I know there are a lot of threads on the OHC already but I couldn't find the answer to my question. I installed my OHC last night, well actually I got done at like 3 am this morning. When I plug the OHC in the map light is on, but nothing else is. When I close my door the light stays on. I had to disconnects the OHC so the light wouldn't drain my battery. Did I not connect the wires correctly? I figure it's the wires that connect behind my stereo so I will check those later and make sure they are making a connection. I followed the walk-through here, http://www.cardomain.com/ride/296394/4 , and did exactly what is posted. Any suggestions would be appreciated.
Thanks for the help! I think this is my first post on here.
Cory
Thanks for the help! I think this is my first post on here.
Cory
#3
I figured out part of it. I had both the wires that went to the dome light connected to the same wire. I moved the black/blue one to the black/blue wire on the dome light and it all worked perfect. I didn't test the dimer though, but I will do that tomorrow.
Thanks for the diagram. Now I just need to find that bit about what area I am so I can sync the navigation part.
Cory
Thanks for the diagram. Now I just need to find that bit about what area I am so I can sync the navigation part.
Cory
#4
#7
Alright Ive looked all over and before I hook this thing up wrong and fry my OHC I need some input please. Here is my pin setup
1 N/U
2 BK Ground
3 GY/Y Power
4 GY/BK GEM
5 GR/OR Dome Light
6 BK/LB Dome Light
7 N/U
8 RD/BK ??????????? I have not seen this on any write up yet I have 3 harnesses with this color
9 LB/Y Temp Sensor
10 LB/W Temp Sensor
1 N/U
2 BK Ground
3 GY/Y Power
4 GY/BK GEM
5 GR/OR Dome Light
6 BK/LB Dome Light
7 N/U
8 RD/BK ??????????? I have not seen this on any write up yet I have 3 harnesses with this color
9 LB/Y Temp Sensor
10 LB/W Temp Sensor
#10
This is what I followed:
1. Black (BK) - ground
2A. Yellow/Gray (YE/GY) - console electronics power
2B. Blue/Red (BL/RD) - console display dimmer input
3A. Green/Orange(GN/OR) - Map light power
3B. Black/Blue(BK/BL) - Dome light power
4A. Lt. Blue/White (BL/WH) - Temp sensor
4B. Lt. Blue/Yellow (BL/YE) - Temp sensor
5. Gray/Black (GY/BK) - speed sensor (not used by some, but necessary)
You can find more here, http://www.cardomain.com/ride/296394/3 , go to page two for more info also.
1. Black (BK) - ground
2A. Yellow/Gray (YE/GY) - console electronics power
2B. Blue/Red (BL/RD) - console display dimmer input
3A. Green/Orange(GN/OR) - Map light power
3B. Black/Blue(BK/BL) - Dome light power
4A. Lt. Blue/White (BL/WH) - Temp sensor
4B. Lt. Blue/Yellow (BL/YE) - Temp sensor
5. Gray/Black (GY/BK) - speed sensor (not used by some, but necessary)
You can find more here, http://www.cardomain.com/ride/296394/3 , go to page two for more info also.
#11
Thread
Thread Starter
Forum
Replies
Last Post
MugenCRX04
OLD - Interior, Exterior, Electrical, & Misc.
12
09-29-2009 03:18 PM
99offroadrngr
General Technical & Electrical
10
05-20-2009 12:01 AM