Center Console Install Quesitons
#1
#2
mine is from an 01....and actually...believe it or not, it bolted right up for me. I took out the cupholders, cut my seat, etc (got everything ready) and it slipped in. There are two rivets that go into 2 holes in the dash. It works out very nicely. I took measurements for drilling from there and then I just pre-drilled my holes for the screws and screwed her in. She holds perfect...if i can get some pics I will.
I would try to get a 01-02 (i think it is) the cupholders IIRC changed around and I like the ones that I have...
heres mine anyway
i can get a pic of the rivets if you want..it will take like 5 mins
I would try to get a 01-02 (i think it is) the cupholders IIRC changed around and I like the ones that I have...
heres mine anyway
i can get a pic of the rivets if you want..it will take like 5 mins
#3
#4
Originally Posted by HighRollerII
yea if you dont mind..them rivets..got me kinda messed up in the head i cant picture what your talkin bout..haha
yea im dieing for one..i just gotta get off my behind and go junkyard diving..
yea im dieing for one..i just gotta get off my behind and go junkyard diving..
brb
#5
thanks man
i was doing some seachin over on GE and found this..so im kinda answerng my own question
http://www.generation-edge.info/topic.asp?TOPIC_ID=3333
i was doing some seachin over on GE and found this..so im kinda answerng my own question
http://www.generation-edge.info/topic.asp?TOPIC_ID=3333
#6
just so ya get the big picture
it's the rivets..not the bolts, i stole the bolts from that computer looking thingy right under the console...i hope that wasn't bad they fit perfect with a little finesse
again, it's the ones on the outer edges (in this pic, the one on the right)
if you have any other questions, let me know. It fits perfect and it's a perfect template to drill holes and such. I was trying to get the console to come out...but i locktited the bolts...sorry man!
it's the rivets..not the bolts, i stole the bolts from that computer looking thingy right under the console...i hope that wasn't bad they fit perfect with a little finesse
again, it's the ones on the outer edges (in this pic, the one on the right)
if you have any other questions, let me know. It fits perfect and it's a perfect template to drill holes and such. I was trying to get the console to come out...but i locktited the bolts...sorry man!
#7
#8
My console is from a '98 or a '99. The front of mine went in the same as Rickey's, I used screws instead of rivets. I also couldn't figure out how to mount the back part of the console so I went to Home Depot and bout some metal angles(I think they are supposed for wood), but I attached those to the bottom of the console and the side of the hump, so I have a couple of screw going throught the floor.
Did you look on eBay for a console? Thats where I got mine.
Did you look on eBay for a console? Thats where I got mine.
#10
#11
hey man, no problem...anything i can do to help!!! B/c one day I might need it! like the maglight...it's been used before, it's pretty handy
i just tucked my airbag switch under the last peice of the console...it's there if i ever need it triggers is better though, i shoulda done it like that!
i just tucked my airbag switch under the last peice of the console...it's there if i ever need it triggers is better though, i shoulda done it like that!
#13
Thread
Thread Starter
Forum
Replies
Last Post
matthewavogt
General Technical & Electrical
0
07-16-2015 01:09 PM
jtkonieczny
Interior Semi-Tech
11
11-08-2011 05:21 PM
gibsondale
General Ford Ranger Discussion
3
04-20-2010 09:03 AM