project power ranger
#1
Join Date: Dec 2008
Location: West Greenwich RI
Posts: 330
Likes: 0
Received 0 Likes
on
0 Posts
project power ranger
so i figured i'd start a project thread
when i first bought the the truck
the first thing i did was build a new rear bumper to replace the rotted out factory one
got a set of rims and some 31x10.5x15 bfg all terrains
then i replaced the radiator support and while i had the front all apart i painted the front clip and engine bay with spray in bed liner
before
after
then i put some explorer visors in
taurus 3.8 maf with a aem dry flow cone filter
prothane cab bushings and 1 inch body lift blocks
then i started replacing all my cross members
before
after
and as of right now i have a 6 inch lift to put on and some explorer springs with bell tech shackles
when i first bought the the truck
the first thing i did was build a new rear bumper to replace the rotted out factory one
got a set of rims and some 31x10.5x15 bfg all terrains
then i replaced the radiator support and while i had the front all apart i painted the front clip and engine bay with spray in bed liner
before
after
then i put some explorer visors in
taurus 3.8 maf with a aem dry flow cone filter
prothane cab bushings and 1 inch body lift blocks
then i started replacing all my cross members
before
after
and as of right now i have a 6 inch lift to put on and some explorer springs with bell tech shackles
#5
Join Date: Dec 2008
Location: West Greenwich RI
Posts: 330
Likes: 0
Received 0 Likes
on
0 Posts
#6
Join Date: Dec 2008
Location: West Greenwich RI
Posts: 330
Likes: 0
Received 0 Likes
on
0 Posts
progress
yesterday i finally finished my body lift, took my carpet out ,and painted my front bumper black. i also gave my dad a call and he's gonna pick me up a chrome shifter and transfer case shifter and boots from an fx4 level 2 from a junk yard he gets parts for work from
painted bumper
no more carpet
painted bumper
no more carpet
#14
Join Date: Dec 2008
Location: West Greenwich RI
Posts: 330
Likes: 0
Received 0 Likes
on
0 Posts
#15
Join Date: Dec 2008
Location: West Greenwich RI
Posts: 330
Likes: 0
Received 0 Likes
on
0 Posts
new parts
well today finnally i went to the junk yard and picked up my b2 gas tank and skid plate i also got my clutch and slave cylinder from advanced auto. the clutch and the gas tank will hopefully be in this weekend
skid plate
my friend cutting the gas tank straps
and my new clutch/ slave cylinder
skid plate
my friend cutting the gas tank straps
and my new clutch/ slave cylinder
#16
#17
Looks like you're doing all the right stuff to 'er... One thing though: In that picture where the bed is off, your sway bar looks hella twisted. Maybe it's just the angle, but I kind of doubt it. It looks just super warped.
Anyway I like what you're doing. Looking forward to what the future holds!
Anyway I like what you're doing. Looking forward to what the future holds!
#23
Join Date: Dec 2008
Location: West Greenwich RI
Posts: 330
Likes: 0
Received 0 Likes
on
0 Posts
Thread
Thread Starter
Forum
Replies
Last Post
FX2.3
Auto Detailing 101
10
05-27-2008 02:26 PM
robert99ranger
General Technical & Electrical
1
05-24-2008 07:32 PM
03DualSport
General Ford Ranger Discussion
1
12-11-2006 04:36 PM
Ranger1
General Technical & Electrical
14
09-23-2005 12:50 PM