Ranger-Forums - The Ultimate Ford Ranger Resource - Search Results

 
Search: Posts Made By: Clinton
Showing results 1 to 25 of 500
Search took 0.05 seconds.
Replies: 9
Views: 1,459
Posted By Clinton

I appreciate it, thank you

I appreciate it, thank you
Replies: 2
Views: 2,207
Posted By Clinton

ttt

ttt
Replies: 9
Views: 1,459
Posted By Clinton

I'm interested if 02 slammed doesn't take them

I'm interested if 02 slammed doesn't take them
Replies: 2
Views: 2,207
Posted By Clinton

Center console / armrest - PA

This is a re-wrapped center console, done by none other than drppdyllwrngr! It is all black vinyl and immaculate! I am selling it for 100.00 shipped or best offer, OR a trade.


...
06-10-2013
Replies: 11
Views: 1,008
Posted By Clinton

Keep the carpet, sell the vinyl and get weather...

Keep the carpet, sell the vinyl and get weather tech floor mats
Replies: 33
Views: 2,989
Posted By Clinton

Bump...the yellow LUND visors are no longer made...

Bump...the yellow LUND visors are no longer made so get this while you can!
05-20-2013
Replies: 2
Views: 1,074
Posted By Clinton

You should be able to pop the plastic cover off...

You should be able to pop the plastic cover off it, then unscrew the light/switch assembly then replace the bulb. It is very easy, just pop the plastic cover off and you will see what has to be done...
05-19-2013
Replies: 8
Views: 1,334
Posted By Clinton

Neither did I lol...I'm still debating the swap...

Neither did I lol...I'm still debating the swap though
05-19-2013
Replies: 4
Views: 2,200
Posted By Clinton

That's good news! Good job!

That's good news! Good job!
05-19-2013
Replies: 8
Views: 1,334
Posted By Clinton

I bought the setup from a member who sold his...

I bought the setup from a member who sold his truck, he never installed it



You are awesome man, thank you!
05-18-2013
Replies: 11
Views: 1,031
Posted By Clinton

Ok, If you don't mind checking they should fit in...

Ok, If you don't mind checking they should fit in a large Flat rate box
05-18-2013
Replies: 11
Views: 1,031
Posted By Clinton

I would do the shipping, I just wanted to make...

I would do the shipping, I just wanted to make sure they were the dual piston type and if they were in better condition than my own so I could swap them out.
05-17-2013
Replies: 1
Views: 887
Posted By Clinton

Try replacing the throttle position sensor. It is...

Try replacing the throttle position sensor. It is bolted on to the throttle body with 2 screws and a plug. They sometimes go which may cause your problem. They run in the area of 60.00 at local auto...
05-17-2013
Replies: 4
Views: 2,200
Posted By Clinton

Usually with a bad cv, from my own experience,...

Usually with a bad cv, from my own experience, will grind and bang around. Check your brake pads, it may be the warnings going off for being too low, or a caliper clip, brake pad clip, may have...
Replies: 19
Views: 1,306
Posted By Clinton

40.00 shipped?

40.00 shipped?
05-16-2013
Replies: 8
Views: 1,334
Posted By Clinton

How to swap coilover eyelets?

I have all the parts to do a coil over swap for my truck. The coil overs came with standard eyelets for the base, but I need to put the extended ones on. I was told by my mechanic that the whole...
05-16-2013
Replies: 11
Views: 1,031
Posted By Clinton

Can you post pics of the calipers?

Can you post pics of the calipers?
Forum: Project Logs
05-14-2013
Replies: 43
Views: 11,017
Posted By Clinton

Pretty much, it was one of the first mods I did....

Pretty much, it was one of the first mods I did. It took me longer because I did the auto mirror and lighted visors at the same time. I just studied the hell out of the directions and had some help...
05-13-2013
Replies: 3
Views: 317
Posted By Clinton

Welcome from another salt belt state!

Welcome from another salt belt state!
05-13-2013
Replies: 1
Views: 597
Posted By Clinton

All step side beds are the same. The topper will...

All step side beds are the same. The topper will fit 93-04 stepside beds
05-13-2013
Replies: 25
Views: 6,189
Posted By Clinton

That looks good man, nice work!

That looks good man, nice work!
Replies: 9
Views: 710
Posted By Clinton

I'm going to try and hit the junkyard this week...

I'm going to try and hit the junkyard this week to get myself a new pair of toggles. I will grab extras if I can get out there
Forum: New Ideas
05-11-2013
Replies: 18
Views: 14,818
Posted By Clinton

I think it goes well with your truck.

I think it goes well with your truck.
Forum: Project Logs
05-11-2013
Replies: 681
Views: 101,327
Posted By Clinton

Great build thread! Truck looks awesome

Great build thread! Truck looks awesome
Forum: Project Logs
05-11-2013
Replies: 43
Views: 11,017
Posted By Clinton

I have wanted them for a long time. The bead...

I have wanted them for a long time. The bead locks make them stand out so much more than the classic II's
Showing results 1 to 25 of 500
 


 

Contact Us - Sitemap - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.