Front Vibration
#1
Front Vibration
Lately my truck has started getting a vibration in the front that comes and goes. Only does it while cruising really, but randomly. From looking at other post, I'm thinking it time to replace the ball joints, wheel bearing, TRE's. The ranger has 124000 miles on it and no front end work has been done except normal brake replacement. What all do i need to replace because not sure I can afford to replace everything up front? Also, does my assumption sound correct that the vibration is coming from one of those components?
#3
#5
Balancing my tires was the first thing i tried. The last time it started doing this balancing my tires fixed/delayed the problem for about a 1000 miles and now its back. Balancing this time had no affect. I also had the tires rotated this time hoping this could be the culprit but to no avail. Would the tires themselves be causing the problem? I ask this because these tires have been horrible to keep balanced.
#6
I would check your front end before replacing everything. Cheaper IMO. Also when was the last time a wheel bearing was done? The bearings might be popping out of the races randomly and causing that front end shake. Go in a big parking lot, and give it a few good hard turns to one side. If it starts to shake after, you have nailed it down.
#8
well, when I bought the truck in 2006 with 42,000 miles, they said nothing had been done up front repair wise, and I haven't had to replace anything other than routine brake work. How often do the bearings go out and are they hard to change? Im gonna go find a parking lot tonight and see what happens, I'll let yall know what I find.
#9
Found an empty parking lot tonight, did hard left and right turns, heard no rattling, growling, groaning sounds...heard some nagging from the passenger seat...but nothing up front. Got on the highway right after and no vibration. Could it still be the wheel bearings? The truck doesn't make any noises other than the noisy engine (another thread for later on) and the only problem I'm having is the intermittent vibration from the front. Should I just live with (not a fan of) or just start throwing parts (and money) at it and hope for the best?
#10
since i have started this thread, haven't had a problem with the truck. Its being too random to diagnose. Does anyone have an idea as to what could cause this? Chainfire...as far as the bearings jumping out of the races temporarily, is there another way to check to see if this is the problem because the parking lot didn't yield anything?
#11
Member
iTrader: (2)
Join Date: Jan 2008
Location: Cary, IL
Posts: 801
Likes: 0
Received 0 Likes
on
0 Posts
I'd jack up a front wheel from your lower control arm (a-arm). and se if you cant wiggle the wheel, try pushing on the top of the wheel while pulling on the bottom. see if you have any free play in your ball joints while looking at them while you do this. then try to wiggle it side to side and check for freeplay in your tierod ends. to feel for a bad wheel bearing i use a long steel pipe and pry on the bottom of my tire and the ground while feeling or hearing for a small "click". also grab ahold of your front axle shaft and twist it by hand, there should only be a small amount of freeplay in and out of the joints no freeplay in the rotation.
this is how i check for front end vibration
this is how i check for front end vibration
#12
finally got around to checking the front end for any play. The only thing I could find was a popping/clicking sound from the front passenger side tire. The noise only happened when I pushed at the top of the tire. There appeared to be no play in the tie rod ends or any where else. What does the clicking noise from pushing at the top of the tire indicate? Wheel bearing or ball joints?
Thread
Thread Starter
Forum
Replies
Last Post
UNCCRang49
Drivetrain Tech
19
09-16-2019 10:16 AM
INT3RC3PTOR
General Technical & Electrical
4
06-16-2008 12:24 AM