Manual 1354 questions! Help!
Thread Starter
|
Member
Joined: Nov 2004
Posts: 4,306
Likes: 0
From: Richmond Hill, Georgia
Manual 1354 questions! Help!
Where the shifter mounts to the tranny, does that huge bolt move? Mine must be seized up or something. I see where there are 2 holes for the shifter to bolt to though.
Next is, where the linkage connects to the t-case to move it through the gears of the t-case, how in the heck does it 'mount'?
Mine has like a slot on the linkage then on the t-case there's like a pin, but I can't figure out how it would stay on that pin? Help?
Brenton
Next is, where the linkage connects to the t-case to move it through the gears of the t-case, how in the heck does it 'mount'?
Mine has like a slot on the linkage then on the t-case there's like a pin, but I can't figure out how it would stay on that pin? Help?
Brenton
Unregistered User
Posts: n/a
theres a plastic bushing that goes on the shifter and the pin on the lever of the t case slides on that bushing. i had to get a new bushing for mine as the one on the bronco II shifter was a mess.
the large bolt once tightened will not move, the shifter pivots on that bolt and that also has a plastic bushing.
this is the only pic i have of my getto fabbed set up
can you take a pic of what you are working with
the large bolt once tightened will not move, the shifter pivots on that bolt and that also has a plastic bushing.
this is the only pic i have of my getto fabbed set up
can you take a pic of what you are working with
Thread Starter
|
Member
Joined: Nov 2004
Posts: 4,306
Likes: 0
From: Richmond Hill, Georgia
This pic is looking towards the rear of the truck (the big bolt is not screwed in, as it is basically frozen):
This is looking at where the shifter 'shifts' the t-case:
Back side of the same pic as above:
The whole thing:
Brenton
This is looking at where the shifter 'shifts' the t-case:
Back side of the same pic as above:
The whole thing:
Brenton
Last edited by EdGe_wannabe; Feb 13, 2008 at 06:12 PM.
Member
Joined: Jan 2005
Posts: 590
Likes: 0
From: North GA
OK.. I am going to try and post my pix in the order you have yours posted..... we will see how that works!!
1 The 'bolt'... Ok... you need to back that bolt out... put some anti seize on it or grease and just thread it in to clear out those threads.. it has to be tight, and how it is now aint right... You are also missing another bolt in the mount area.. you can see it in mine...
2 wasn't able to get a good pic of mine but mine fits pretty flat against it...
3 no pic of this, couldn't get in there cause of my mount and skid plate.. BUT mine is the same from what i could feel, just a pin and nothing else.. not sure how it keeps itself from backin out... but it does lol
4
1 The 'bolt'... Ok... you need to back that bolt out... put some anti seize on it or grease and just thread it in to clear out those threads.. it has to be tight, and how it is now aint right... You are also missing another bolt in the mount area.. you can see it in mine...
2 wasn't able to get a good pic of mine but mine fits pretty flat against it...
3 no pic of this, couldn't get in there cause of my mount and skid plate.. BUT mine is the same from what i could feel, just a pin and nothing else.. not sure how it keeps itself from backin out... but it does lol
4
Unregistered User
Posts: n/a
the bushing is missing for the shifter to t case lever.
the bolt, well your going to have to remove the shifter and take it apart and un freeze the bolt and probley get a new bushing for that also.
i had to do the same thing with mine.
or you could buy a new shifter assmly from ford for 200 bucks
the bolt, well your going to have to remove the shifter and take it apart and un freeze the bolt and probley get a new bushing for that also.
i had to do the same thing with mine.
or you could buy a new shifter assmly from ford for 200 bucks
Thread
Thread Starter
Forum
Replies
Last Post
exploder01
OLD - Engine & Drivetrain
19
Sep 12, 2009 07:04 PM
