Where Is The 4x4 Control Module On A 98?
Member
Joined: Oct 2005
Posts: 2,804
Likes: 6
From: Northern IL
I doubt your 4wd control module theory.
Based on.
Being that you have a 98 and PVH hubs. Im willing to bet the hubs are your problem. Or a shift motor. Try this https://www.ranger-forums.com/forum2...ead.php?t=9211
The GEM is located next to the radio on the left.
Based on.
Module Controlled Functions
The multifunction modules consist of the following:
l generic electronic module (GEM)/central timer module (CTM)
l remote anti-theft personality (RAP) module (15K602)
The remote anti-theft personality (RAP) module controls the keyless entry, and computer operated locks systems.
The GEM/CTM controls the following features:
l wiper/washer (front/rear)
l warning chime
l battery saver
l illuminated entry and courtesy lamps
l driver one touch down power window (GEM only)
l accessory delay
l 4 wheel drive (GEM only)
The multifunction modules consist of the following:
l generic electronic module (GEM)/central timer module (CTM)
l remote anti-theft personality (RAP) module (15K602)
The remote anti-theft personality (RAP) module controls the keyless entry, and computer operated locks systems.
The GEM/CTM controls the following features:
l wiper/washer (front/rear)
l warning chime
l battery saver
l illuminated entry and courtesy lamps
l driver one touch down power window (GEM only)
l accessory delay
l 4 wheel drive (GEM only)
The GEM is located next to the radio on the left.
Thread Starter
|
Member
Joined: Feb 2008
Posts: 8
Likes: 0
From: AUBURNDALE,FL
module
All I get when I switch to 4hi or 4 low is both lights flashing on the dash. I got under the truck and the shift motor does nothing upon flipping the 4x4 switch. I ordered a new t. case motor from Summit racing. As soon as that comes ill try that. If not that then what? I assume all i have to do is install the new t. case motor. just bolt it on right? any adjustments needed first? I just bought the truck for my son a week ago. The guy told me everything worked. yeh right!!!!!
Member
Joined: Oct 2005
Posts: 2,804
Likes: 6
From: Northern IL
Flashing lights mean the shift motor is stuck in between shifts.
It can be cleaned. Some have had good results with that. YMMV
http://www.therangerstation.com/tech...shiftmotor.htm
It can be cleaned. Some have had good results with that. YMMV
http://www.therangerstation.com/tech...shiftmotor.htm
Thread Starter
|
Member
Joined: Feb 2008
Posts: 8
Likes: 0
From: AUBURNDALE,FL
Fixed it!! Well Almost!!
Got the new shift motor today. installed it and it worked!!! But problem is that my vaccum hubs are crapped out so I did the " little fix" and removed that little silver clip from the hubs. My 4x4 works
I have locked hubs for about 3 weeks until the AVM hubs come in. I hope locked hubs don't cause any problems! So my problem was 2 fold!!! Thanks for the help all
I have locked hubs for about 3 weeks until the AVM hubs come in. I hope locked hubs don't cause any problems! So my problem was 2 fold!!! Thanks for the help all
Thread
Thread Starter
Forum
Replies
Last Post
For Sale: 4x4 Control module for 01-06 Ranger
Donnyd21
OLD - Interior, Exterior, Electrical, & Misc.
1
Jun 8, 2020 03:38 PM
Want to Buy: 2001-2002 4x4 module
SPYDER0382
OLD - Interior, Exterior, Electrical, & Misc.
3
Dec 8, 2010 07:02 AM
