Fog Light Mounting Bolts
#1
Fog Light Mounting Bolts
I recently bought some stock style square fog lights for my 06 xl. I have the stock lights, mounts, bulbs, ect just rockauto didn't have the stock mounting bolts for the foglight hardware. The ones that actually mount the brackets to the bumper itself.
Anyone have the part numbers, picture layout that shows part numbers, or the measurements on them, etc etc. I can't seem to find access to the picture layouts that ford uses and even searched for the part numbers and couldn't find anything. Any help would be great.
Thank
Anyone have the part numbers, picture layout that shows part numbers, or the measurements on them, etc etc. I can't seem to find access to the picture layouts that ford uses and even searched for the part numbers and couldn't find anything. Any help would be great.
Thank
#3
Old Guy User…
iTrader: (12)
What about Tasca Ford, they have Ford Parts at a discount.
http://www.tascaparts.com/partlocato...?siteid=213668
Is your bumper setup for the Fogs ?
Whats there ?
http://www.tascaparts.com/partlocato...?siteid=213668
Is your bumper setup for the Fogs ?
Whats there ?
#5
Old Guy User…
iTrader: (12)
good call: http://www.lmctruck.com/icatalog/fr/full.aspx?page=140
It appears LMC has a Clip Nut and Screw, not a hard thing to pickup at the local hdw store as meistreguy has suggested.
It appears LMC has a Clip Nut and Screw, not a hard thing to pickup at the local hdw store as meistreguy has suggested.
Last edited by Scrambler82; 03-06-2012 at 08:41 AM.
#6
I looked at that link on tasca parts and mines the square fog light design for my 06 which in the link isnt showing any screw or bolt for that specific one. I know I could probably go to the hardware store and find something to work but I was hoping to atleast know the dimensions of it to try and make it perfect or something you know.
#7
What about Tasca Ford, they have Ford Parts at a discount.
http://www.tascaparts.com/partlocato...?siteid=213668
Is your bumper setup for the Fogs ?
Whats there ?
http://www.tascaparts.com/partlocato...?siteid=213668
Is your bumper setup for the Fogs ?
Whats there ?
EDIT: I talked to a guy I know from tasca and he finally got back to me on an answer. They are indeed bolts for the square fogs and they are M6 x 1.0 so hopefully I can pick some up locally.
Last edited by ZWilson07; 03-06-2012 at 03:45 PM.
#8
Old Guy User…
iTrader: (12)
As far as this yes my bumper is setup for fogs and I have everything I need, foglights, bulbs, pig tails, and mounting brackets. The only thing I need are the 3 mounting bolts or scews that mount the brackets to the inside of the bumper itself.
EDIT: I talked to a guy I know from tasca and he finally got back to me on an answer. They are indeed bolts for the square fogs and they are M6 x 1.0 so hopefully I can pick some up locally.
EDIT: I talked to a guy I know from tasca and he finally got back to me on an answer. They are indeed bolts for the square fogs and they are M6 x 1.0 so hopefully I can pick some up locally.
They show just three clips and screws.
sounds like a hardware store run if the above is true.
ltr
#9
But I did get ahold of my guy from tasca and he did comfirm for me that it is just 3 of those bolts I mentioned for the 06 square style mounts, not screws or clips. That is for the different style and gen bumpers and fogs.
#11
I did not know that the newer vehicles required brackets as well. I have an "02 XLT in which I am going with a 4X4 bumper to put the driving lights in. I will be going to Home Depot to get the bolts but I lucked out since the driving lights I got are LED version and should look killer! Only 71.99 shipped to me so I couldn't pass it up!
#12
Thread
Thread Starter
Forum
Replies
Last Post
MugenCRX04
OLD - Interior, Exterior, Electrical, & Misc.
13
03-28-2011 04:41 PM
ladenblowfish
General Technical & Electrical
9
11-10-2010 01:19 PM
Ranger_Envy
General Technical & Electrical
3
07-27-2009 09:05 PM
melj2000
General Technical & Electrical
2
09-28-2007 11:12 AM