Post pics of your off road lights on your bumpers
cant really see them too well but they are mounted on tabs bolted in from behind the bumper, got them from www.stuffforyourranger.com
https://www.ranger-forums.com/forum2...ght=light+tabs
^^That's a link to a how-to on doing your own light tabs. No Drilling to your truck at all. Works on 98-05 trucks. I have no clue if your truck has the bolts in the right places, but this is the best option, imo, if your don't want to drill into your bumper.
Here's mine:
Before with virtually the same measurements as Wayne's tabs, but with the Slimlites.
Homemade lite tabs....using 1/4"x1 1/2". Bent using oxy/acet torch on a vice. Eyeballed it. I shortend them up to hug against the grille by about 1.5" compaired to my old tabs. KC Slimlite Titaniums(thanks 07ranger!!). I'm going to add two more lites in the middle here like next week.
Comparison between my old tabs and my new tabs. I believe I followed the diagram of what Jusnes and Underdog sells when i made the first set...except for the thickness of the first set of tabs.
Then you could add a crossmember, and bam! you got 4 lights!
^^That's a link to a how-to on doing your own light tabs. No Drilling to your truck at all. Works on 98-05 trucks. I have no clue if your truck has the bolts in the right places, but this is the best option, imo, if your don't want to drill into your bumper.
Here's mine:
Before with virtually the same measurements as Wayne's tabs, but with the Slimlites.
Originally Posted by Fx4wannabe01
Homemade lite tabs....using 1/4"x1 1/2". Bent using oxy/acet torch on a vice. Eyeballed it. I shortend them up to hug against the grille by about 1.5" compaired to my old tabs. KC Slimlite Titaniums(thanks 07ranger!!). I'm going to add two more lites in the middle here like next week.
Comparison between my old tabs and my new tabs. I believe I followed the diagram of what Jusnes and Underdog sells when i made the first set...except for the thickness of the first set of tabs.
I'm like pictures too! Mine is a tad custom but they're ligths mounted on my bumper 
From a distance
Little Closer (rough roads will do that to my covers, littl upside down, lol)
Best shot I have of the light tab
From a distance
Little Closer (rough roads will do that to my covers, littl upside down, lol)
Best shot I have of the light tab
Member
Joined: Aug 2006
Posts: 647
Likes: 1
From: Pensacola, FL
If you're talking about the light tabs for the bumpers it doesn't matter. The tabs are attatched directly to the bumper and go where ever the bumper goes (you take the bumper off, the lights come off. You lift the bumper with lift brackets, the lights go up 3" with the bumper). Wayne recently had a thread on how to make some since he's having problems bending them right now.
If you're talking about the light tabs for the bumpers it doesn't matter. The tabs are attatched directly to the bumper and go where ever the bumper goes (you take the bumper off, the lights come off. You lift the bumper with lift brackets, the lights go up 3" with the bumper). Wayne recently had a thread on how to make some since he's having problems bending them right now.
To elaborate on this.....
The light tabs are attached using an existing bumper bolt. To install lite/light tabs, take the bolt out, put the tab against the bumper, run the bolt through the tab then into the nutsert, then tighten the bolt.
The PA bodylift brackets, i believe, use the stock mounting spots on the bumper to mount.......so your good to go there, just a little differnt being that the PA kit uses bolts and nuts, unlike the stock bolt into fixed nut. If i'm wrong, you could always just use a 3/8 bolt & nut through the hole in the bumper where the light tabs normally mount.
These pics are the best pics i got in regard to location........basically under the bottom corners of the grille, backside of bumper....
Thread
Thread Starter
Forum
Replies
Last Post
TheBearJeweler
OLD - Interior, Exterior, Electrical, & Misc.
12
May 11, 2009 12:55 PM
