4.0L OHV & SOHC V6 Tech General discussion of 4.0L OHV and SOHC V6 Ford Ranger engines.

Fuel filter disconnect trick.

Thread Tools
 
Search this Thread
 
Old Apr 27, 2009
  #1  
IN2 FX4's Avatar
Thread Starter
|
Member
Joined: Feb 2005
Posts: 1,269
Likes: 115
From: Costa Mesa, CA
Fuel filter disconnect trick.

I have seen a lot of posts regarding difficulty in disconnecting the fuel lines from the filter. This weekend I replaced my fuel filter and discovered an easy way to disconnect them. At least it works well on my 02.

If you look at the fitting on the fuel line you should find a tab or long button looking device on one side that is flush with the outer diameter of the fitting. Mine were either orange or green depending on which line it was. I found if I pressed in on this tab/button with my thumb nail, it would easily release the line fitting from the filter. You could use a screw driver also but I found it easier to wrap one hand around the fitting and use my thumb nail to push the tab/button in while holding the filter with the other hand to pull them apart.

I did use a tool to disconnect one of them but was having trouble getting the larger line to disconnect with the tool. I decided to try pushing in on that tab/button and it practically fell apart. I am glad I like to experiment because that job will be a lot easier now.
 
Reply
Old Apr 27, 2009
  #2  
MemphisSenior's Avatar
Member
Joined: Mar 2007
Posts: 331
Likes: 1
From: Spring City, TN
Thanks Gary. Good tip. I'll try it next time I change mine.
 
Reply
Old Apr 27, 2009
  #3  
Fx4wannabe01's Avatar
RF Veteran
iTrader: (23)
Joined: May 2005
Posts: 21,721
Likes: 17
From: Boring, Oregon
Pushing in that green and orange with my fingernail is how i do mine.

On '01+ trucks, you dont need any special tooling to disconnect the fuel lines from the filter.
 
Reply
Old Apr 27, 2009
  #4  
04blackedge's Avatar
RF Veteran
iTrader: (13)
Joined: Jan 2007
Posts: 23,426
Likes: 8
From: Durham, NC
Thats how I did mine as well, super easy.
 
Reply
Old Apr 27, 2009
  #5  
robert99ranger's Avatar
RF Veteran
iTrader: (4)
Joined: Aug 2007
Posts: 5,809
Likes: 4
From: Indiana/Mississippi
So I need a special tool on my 99 then?
 
Reply
Old Apr 27, 2009
  #6  
Blhde's Avatar
Member
Joined: Oct 2005
Posts: 2,804
Likes: 6
From: Northern IL
Originally Posted by robert99ranger
So I need a special tool on my 99 then?
Yup.

It helps to push the line onto the filter more then installing the tool, while you still try and push it onto the filter.

You may need to wiggle the line a bit. It should slide off easily if you have released the lock.


Make sure there is no pressure on the system. It will go everywhere. Being that your face is right there. Its not a good time.
 
Reply
Old Apr 27, 2009
  #7  
Downey's Avatar
RF Veteran
iTrader: (1)
Joined: Oct 2007
Posts: 8,470
Likes: 6
From: Muncy, PA
I dont remember how i took mine apart on my 94 but i didnt need a special tool to get it off i just got the clips off and then slid the lines off
 
Reply
Old Apr 27, 2009
  #8  
redranger4.0's Avatar
Member
Joined: Jun 2004
Posts: 15
Likes: 0
From: Firey depths
my 2000 had plastic clips you pull out and the filter comes out no special tool needed. Up by the motor there is a spring style fiting that needed a tool though.
 
Reply
Old Apr 27, 2009
  #9  
chevyslayer925's Avatar
Member
iTrader: (4)
Joined: Jan 2008
Posts: 1,293
Likes: 0
From: Trexlertown,Pennslyvania
i need to do this to mine yet. . .ive been putting it off for some time now.
 
Reply
Old Apr 28, 2009
  #10  
99_NWRanger's Avatar
Member
Joined: Apr 2008
Posts: 331
Likes: 0
From: WA / Mountain Home, ID
Yeah, I haven't changed my fuel filter out the entire time I've had my truck! I think I should do it soon! hah
 
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
iplayloudly
OLD - Interior, Exterior, Electrical, & Misc.
7
May 2, 2012 03:10 PM
Bobby
2.9L & 3.0L V6 Tech
3
Dec 1, 2011 06:23 PM
ranger99ct
General Technical & Electrical
5
Jul 30, 2011 07:16 AM
Takeda
General Technical & Electrical
10
Jul 8, 2010 04:34 PM
lostguitarist
General Technical & Electrical
12
Jan 8, 2009 04:38 PM




All times are GMT -6. The time now is 04:10 PM.