Ranger-Forums - The Ultimate Ford Ranger Resource

General Ford Ranger Discussion General discussion of the Ford Ranger that does not fit in any other sub-forum.

Bed width, 07 Stranger?

   
Old Apr 4, 2007
Share
  #1  
UnlikelyHero's Avatar
Thread Starter
|
Member
Joined: Feb 2007
Posts: 35
Likes: 0
From: Minot Air Base
Bed width, 07 Stranger?
I need to know if a DS 650 will fit in the back, stock wheel width on a DS is 48 inches. I am pretty sure it won't fit, but its worth a shot.
 
Reply
0
Old Apr 4, 2007
Share
  #2  
zabeard's Avatar
who?
iTrader: (8)
Joined: Nov 2004
Posts: 26,044
Likes: 10
From: IN
per Ford's site...

Width – between wheelhouses (in.) = 40.5

But you could just run it over those humps should be fine then
 
Reply
0
Old Apr 4, 2007
Share
  #3  
UnlikelyHero's Avatar
Thread Starter
|
Member
Joined: Feb 2007
Posts: 35
Likes: 0
From: Minot Air Base
Yah my 400ex fits right in between those, barely. The tires rub until they are thru and then there is like 4 inches on each side. I hope it fits, if it doesn't that means I can't take it anywhere.


Thanks btw.
 
Reply
0
Old Apr 4, 2007
Share
  #4  
Trevelyn1015's Avatar
Still El Presidente...
Joined: May 2004
Posts: 4,903
Likes: 6
From: Texas
you could always find a cheap trailer, worst case scenario.
 
Reply
0
Old Apr 4, 2007
Share
  #5  
zabeard's Avatar
who?
iTrader: (8)
Joined: Nov 2004
Posts: 26,044
Likes: 10
From: IN
well i find that 40.5 hard to believe because the track width on the 400ex is like 42" my bed is spread 43" and i have the flareside...
 
Reply
0
Old Apr 5, 2007
Share
  #6  
D94R's Avatar
Member
Joined: Dec 2006
Posts: 731
Likes: 0
From: Lehi, Utah
According to the truck tool box catalogs I've been looking at, the inside width from bed rail to rail, is 49". It sure would be a tight fit.
 
Reply
0
Old Apr 5, 2007
Share
  #7  
UnlikelyHero's Avatar
Thread Starter
|
Member
Joined: Feb 2007
Posts: 35
Likes: 0
From: Minot Air Base
KK sweet, I might just keep the 400 and put some +2 A-arms and lower that bish.
 
Reply
0
Old Apr 6, 2007
Share
  #8  
texasbullseye89's Avatar
Joined: Jan 2006
Posts: 827
Likes: 1
From: Huntsville, Tx
My outlander 400 fits in going over the humps. Most of the Can-Am atv's are the same dimensions.
 
Reply
0
Old Apr 6, 2007
Share
  #9  
UnlikelyHero's Avatar
Thread Starter
|
Member
Joined: Feb 2007
Posts: 35
Likes: 0
From: Minot Air Base
The DS is one wide mother though, like its unreal.
 
Reply
0
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Stranger on board
TyStranger
Member Introductions
9
Jun 3, 2011 12:22 PM
New ranger to the stranger club...
JLA
Member Introductions
6
Oct 3, 2010 04:52 AM
stranger vibration
dracowing14
General Ford Ranger Discussion
3
Jan 27, 2010 05:47 PM
Tire Width/Rim Width Question
TurdFX4
Wheels & Tires Semi-Tech
8
Jan 2, 2010 09:30 AM
The Ranger pulls through again! Towed a stranger home tonight...
AgPete139
General Ford Ranger Discussion
21
Sep 26, 2007 11:17 AM
Back to Subforum
General Ford Ranger Discussion
View Next Unread
My Turn Showing off My POLISHED DC-1's


Thread Tools
Search this Thread
Search this Thread:

Advanced Search

Advanced Search

All times are GMT -6. The time now is 02:40 AM.