Looking at ordering up some Scavenger Cold Rolled Angle Cut tips for fixing my exhaust up, I've got 2 1/4" piping from my muffler back, with my current tip being a 2 1/2" dual exit:
The opinions I am looking for.. is should I order up a 3.00" exit, or a 3.50" exit? Or heck, even a 4", the price ddoesnt bug me at all right now... And in terms of exhaust noise.. I do like it deep toned from my headers/intake/muffler setup.
Give any thoughts/opinions..!!
For reference, this is where I am ordering from, and the cost for the tips is roughly $49-$54 apiece, Stainless Steel, and they are 20" long in total
http://stainlesssteelmufflers.com/tips.htm#htangle
Angle Cut Scavenger Pipe
16 gauge 304 stainless steel. Approximately 20" overall.
Available in 2.50", 3.00", 3.50" and 4.00" outside diameter.
SP300225AN 2.25" 3.00" Angle Cut Polish $49.00
SP350225AN 2.25" 3.50" Angle Cut Polish $54.00
SP400225AN 2.25" 4.00" Angle Cut Polish $59.00
The opinions I am looking for.. is should I order up a 3.00" exit, or a 3.50" exit? Or heck, even a 4", the price ddoesnt bug me at all right now... And in terms of exhaust noise.. I do like it deep toned from my headers/intake/muffler setup.
Give any thoughts/opinions..!!
For reference, this is where I am ordering from, and the cost for the tips is roughly $49-$54 apiece, Stainless Steel, and they are 20" long in total
http://stainlesssteelmufflers.com/tips.htm#htangle
Angle Cut Scavenger Pipe
16 gauge 304 stainless steel. Approximately 20" overall.
Available in 2.50", 3.00", 3.50" and 4.00" outside diameter.
SP300225AN 2.25" 3.00" Angle Cut Polish $49.00
SP350225AN 2.25" 3.50" Angle Cut Polish $54.00
SP400225AN 2.25" 4.00" Angle Cut Polish $59.00
4", that way it'll sound deeper AND it will "fit" the size of your truck, even if you lift more.
Quote:
I was actually 'just' looking at your post in that other Exhaust thread.. Theres a good one for 4", any other opinions folks? Originally Posted by Oh5Edge
4", that way it'll sound deeper AND it will "fit" the size of your truck, even if you lift more.
I think my tips are 3.5" wide and around 22" long!
And im glad to see your going with stainless, i originally had chrome tips and after about 3 years of heavy winter abuse they got to the point of no return. That's why I got my stainless tips last summer
And im glad to see your going with stainless, i originally had chrome tips and after about 3 years of heavy winter abuse they got to the point of no return. That's why I got my stainless tips last summer
Here's my old 2.5" in/3.5" out x 18" angle cut.....looked killer! Sounded killer!
In my opinion.......two 4" tips on a little ford ranger? 3.5" is more than big enough for it......it's just sweet as hell with a 3.5. do it. do it. 4 is overkill imo.
In my opinion.......two 4" tips on a little ford ranger? 3.5" is more than big enough for it......it's just sweet as hell with a 3.5. do it. do it. 4 is overkill imo.
Quote:
Originally Posted by Fx4wannabe01
4 is overkill imo.
It all depends on the application.
I thought that 3" looked too small on mine. So I switched to these ^^^ 4"
Okay.....i retract my previous statement. 4" looks effin' bad ***!
Quote:
Originally Posted by Fx4wannabe01
Okay.....i retract my previous statement. 4" looks effin' bad ***!
Yep, thats what I was thinking when I started browsing around.. plus the tone of note is MUCH deeper and more of a growl then what I've got now.. and considering the mods Ive got in that will change teh sound.. I -think- I will go ahead and order up the 4" angle cut ones
Quote:
Agreed ftwOriginally Posted by Fx4wannabe01
Okay.....i retract my previous statement. 4" looks effin' bad ***!
I'll be going with 3.5" for mine. Even those 0h5edge's looks good too.
