General Ford Ranger Discussion General discussion of the Ford Ranger that does not fit in any other sub-forum.

Superlift install help - WA

Thread Tools
 
Search this Thread
 
Old Dec 7, 2011
  #1  
mikerider's Avatar
Thread Starter
|
Member
iTrader: (8)
Joined: Oct 2006
Posts: 2,518
Likes: 11
From: Renton WA
Superlift install help - WA

So I just found out I have access to a covered warm garage with a lift to install my lift kit on Friday!

Anyone in the area not doing anything and want to lend a hand? Its always nice to have a friend or two to help, I have all the tools we will need. Getting started around 9am.

Thanks guys

-Mike
 
Reply
Old Dec 7, 2011
  #2  
xp1ik99's Avatar
Member
iTrader: (5)
Joined: Feb 2006
Posts: 3,230
Likes: 2
From: Lexington Park, MD
im going to hate your truck when you put it on, that is all i have to say at the moment


if you were on the other coast id be there, its a breeze to install.......
 
Reply
Old Dec 7, 2011
  #3  
mikerider's Avatar
Thread Starter
|
Member
iTrader: (8)
Joined: Oct 2006
Posts: 2,518
Likes: 11
From: Renton WA
Originally Posted by xp1ik99
im going to hate your truck when you put it on, that is all i have to say at the moment


if you were on the other coast id be there, its a breeze to install.......
haha thanks man, I have the rear done already with expo springs just have the front left to do and it looks fairly easy, just nice to have an extra set of hands, got a whole bunch of new stuff from MOOG to go along with the lift so should be nice!
 
Reply
Old Dec 7, 2011
  #4  
xp1ik99's Avatar
Member
iTrader: (5)
Joined: Feb 2006
Posts: 3,230
Likes: 2
From: Lexington Park, MD
i bet, im jealous man cause i like your truck not lifted, hardest part for me was getting that damn bolt out of the side of the diff to put that drop bracket on, for some reason mine didnt want to come out, btw i only had about 40k on my truck lol........should be fun!!!!!!!
 
Reply
Old Dec 7, 2011
  #5  
mikerider's Avatar
Thread Starter
|
Member
iTrader: (8)
Joined: Oct 2006
Posts: 2,518
Likes: 11
From: Renton WA
ya I was worried bolts would be bad but so far so good (fingers crossed) the truck has lived a good life with covered parking and regular washes so the chassis looks almost new.

I like the truck as it sits now but off road the rear would rub when flexed out, and has bent up the inside front of the wheel well on both sides. the explorer springs fixed the rubbing but now I need to level it out, and I want to be able to uncrank the bars and get my ride back. so the plan is to only go up 3in or so. to re level the truck.
 
Reply
Old Dec 7, 2011
  #6  
FULLSCALE's Avatar
Level III Supporter
iTrader: (12)
Joined: Mar 2009
Posts: 8,184
Likes: 4
From: Clinton, Ontario
I'd give you a hand but that's a little too long a drive... if you have any questions during the install post them up! It's pretty straightforward though.
 
Reply
Old Dec 8, 2011
  #7  
Deerchser's Avatar
Member
Joined: Oct 2011
Posts: 33
Likes: 0
From: Arlington, WA
Originally Posted by mikerider
So I just found out I have access to a covered warm garage with a lift to install my lift kit on Friday!

Anyone in the area not doing anything and want to lend a hand? Its always nice to have a friend or two to help, I have all the tools we will need. Getting started around 9am.

Thanks guys

-Mike
You mean as in tomorrow Firday? I might be able to lend you a hand. Let me know and give me a address.
 
Reply
Old Dec 8, 2011
  #8  
mikerider's Avatar
Thread Starter
|
Member
iTrader: (8)
Joined: Oct 2006
Posts: 2,518
Likes: 11
From: Renton WA
Originally Posted by Deerchser
You mean as in tomorrow Firday? I might be able to lend you a hand. Let me know and give me a address.
Yep tomorrow as in friday lol, address is 221 washington ave north Kent WA. I will shoot you a PM with my phone and stuff when I get home from work, an extra hand would be much appreciated!
 
Reply
Old Dec 8, 2011
  #9  
Deerchser's Avatar
Member
Joined: Oct 2011
Posts: 33
Likes: 0
From: Arlington, WA
Sounds good to me. I will see if I have the gas cash to get down there but I think I do. What time do you want to start? I will need to be back up north by around 4. have a date with my wife.
 
Reply
Old Dec 8, 2011
  #10  
mikerider's Avatar
Thread Starter
|
Member
iTrader: (8)
Joined: Oct 2006
Posts: 2,518
Likes: 11
From: Renton WA
Originally Posted by Deerchser
Sounds good to me. I will see if I have the gas cash to get down there but I think I do. What time do you want to start? I will need to be back up north by around 4. have a date with my wife.
I am going to start around 9am when the place opens, I will give you a few bucks for gas and some lunch if come on by!
 
Reply
Old Dec 8, 2011
  #11  
Deerchser's Avatar
Member
Joined: Oct 2011
Posts: 33
Likes: 0
From: Arlington, WA
I will be there as close to 9 as I can. See you then.
 
Reply
Old Dec 8, 2011
  #12  
mikerider's Avatar
Thread Starter
|
Member
iTrader: (8)
Joined: Oct 2006
Posts: 2,518
Likes: 11
From: Renton WA
Thanks man I sent you a PM with my contact info and stuff see you in the morning!
 
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Scrambler82
Suspension Tech
15
Aug 25, 2009 02:21 PM
k.blakeley
Suspension Tech
68
Oct 14, 2007 12:28 PM
Lefty04LevelII
Suspension Tech
7
Aug 16, 2007 06:57 PM
wolfman00
Suspension Tech
11
Jul 13, 2007 09:50 PM
Gearhead61
General Ford Ranger Discussion
3
Jun 17, 2005 08:30 AM




All times are GMT -6. The time now is 02:54 AM.