Python Alarm Issues HELP!!
#1
Python Alarm Issues HELP!!
I recently installed a Python 3305P 2 way alarm system in my 95 ranger. Im having issues entering programming mode on the module, I'm following the instructions perfectly which is to open door, key on, key off, press and hold valet button. I get no response when i do this, im only able to enter and exit valet mode.
Here is how i have wired everything:
12- Pin Harness
Orange (-) 500mA Armed Output -----> Starter (Red/Light Blue (+)
White (+/-) Selectable Parking Light Output -----> Parking Lights (White/Black (-)
White/Blue (-) 200mA Channel 3 Programmable Output ----> NOT USED
Black/White (-) 200mA Domelight Supervision -----> NOT USED
Green (-) Door Trigger Input, Zone 3 -----> NOT USED
Blue (-) Instant Trigger Input, Zone 1 ----> NOT USED
Violet (+) Door Trigger Input, Zone 3 ----> Door Trigger (Black/Light Blue (+)
Black (-) Chassis Ground Input ------> Ground
Yellow (+) Switched Ignition Input, Zone 5 -----> Ignition (Green/Purple (+)
Brown (+) Siren Output ----> 514N Programmable Siren (Red (+)
Red (+) Constant Power Output -----> 12V Constant (Yellow (+)
Red/White (-) 200mA Channel 2 Output ----> NOT USED
Door Lock Harness
Light Blue (-) Unlock, (+) Lock Output -----> Power Unlock (Pink/Light Green (-)
Green (-) Lock, (+) Unlock Output ----> Power Lock (Pink/Yellow (-)
Also, If i arm the system, im able to reach through the window to unlock the door and open it, doing this will not trip the alarm as it should. I believe this has to do with the door trigger wire, which also may be the reason i cant enter programming mode because of that door trigger wire.
With the key in the ON position, if i open the door my domelight turns on, when i close the door the domelight turns off
With the key in the OFF position my domelight will stay on whether i open or close my door and will not turn off. ( This has always been like this, even before i installed anything)
that is an indicator to me that its not receiving a voltage change when my key is off which might explain being unable to get into programming mode since it relys on ignition and opening the door to get into it.
and lastly my siren worked initially, but now its no longer chirping or making any noise. i dont think i programmed it off since i cant get into programming mode. but it stopped working after i checked my wiring (which everything is connected and good) and after i played around with trying to enter and exit programming mode with different combinations
Anyone that can help me out with any of these issues, it would be a big help cause im kind of bummed i spent $250 for features i want but cant enable as well as an alarm that is silent :(
Here are the sources ive used:
https://www.the12volt.com/installbay...etail/907.html
1995-1997 Ford Ranger Vehicle Wiring Chart and Diagram
Here is how i have wired everything:
12- Pin Harness
Orange (-) 500mA Armed Output -----> Starter (Red/Light Blue (+)
White (+/-) Selectable Parking Light Output -----> Parking Lights (White/Black (-)
White/Blue (-) 200mA Channel 3 Programmable Output ----> NOT USED
Black/White (-) 200mA Domelight Supervision -----> NOT USED
Green (-) Door Trigger Input, Zone 3 -----> NOT USED
Blue (-) Instant Trigger Input, Zone 1 ----> NOT USED
Violet (+) Door Trigger Input, Zone 3 ----> Door Trigger (Black/Light Blue (+)
Black (-) Chassis Ground Input ------> Ground
Yellow (+) Switched Ignition Input, Zone 5 -----> Ignition (Green/Purple (+)
Brown (+) Siren Output ----> 514N Programmable Siren (Red (+)
Red (+) Constant Power Output -----> 12V Constant (Yellow (+)
Red/White (-) 200mA Channel 2 Output ----> NOT USED
Door Lock Harness
Light Blue (-) Unlock, (+) Lock Output -----> Power Unlock (Pink/Light Green (-)
Green (-) Lock, (+) Unlock Output ----> Power Lock (Pink/Yellow (-)
Also, If i arm the system, im able to reach through the window to unlock the door and open it, doing this will not trip the alarm as it should. I believe this has to do with the door trigger wire, which also may be the reason i cant enter programming mode because of that door trigger wire.
With the key in the ON position, if i open the door my domelight turns on, when i close the door the domelight turns off
With the key in the OFF position my domelight will stay on whether i open or close my door and will not turn off. ( This has always been like this, even before i installed anything)
that is an indicator to me that its not receiving a voltage change when my key is off which might explain being unable to get into programming mode since it relys on ignition and opening the door to get into it.
and lastly my siren worked initially, but now its no longer chirping or making any noise. i dont think i programmed it off since i cant get into programming mode. but it stopped working after i checked my wiring (which everything is connected and good) and after i played around with trying to enter and exit programming mode with different combinations
Anyone that can help me out with any of these issues, it would be a big help cause im kind of bummed i spent $250 for features i want but cant enable as well as an alarm that is silent :(
Here are the sources ive used:
https://www.the12volt.com/installbay...etail/907.html
1995-1997 Ford Ranger Vehicle Wiring Chart and Diagram
Last edited by Almightyjake; 07-12-2019 at 06:04 PM.
Thread
Thread Starter
Forum
Replies
Last Post
sidmuchrock
General Technical & Electrical
2
11-16-2017 07:40 AM
Drayke
General Technical & Electrical
13
01-16-2008 08:50 PM