i need it on mine

 

Looks like everyone had fun! I can't wait for my meet in May!

Wow, so you still can't accept when you're wrong so you have to try and make other people look like the idiots. This isn't doing anything but making you look like a little immature kid for bringing this back up. So I congratulate you Mark, glad to know you turned 13 this year.

Again with the bashing. You just don't quit do you?! Get a life dude.

 

It was all in good fun. No bashing. Twas a fun meet with lots of excitement!

 

Tre, just let him be the deuche and ***** that he really is, and he'll just get banned again...

 

Tre, calm down. We had accepted your advice on heating coils up, no bashing intended, seriously. Now what do you think can be done with my leaf springs. I want to lower the rear of my 01 to level it out, since I don't want to crank torsion bars. Do you know what type of metal it is? How hot should I get the whole leaf spring? And should I unbolt the rear end before I do it? I just havent heard anything good about cranking torsion bars so I figure I'll just heat up the leafs and lower the back.. Let me know please..
I think we might also lower the front of Josh's truck more by either cutting the coils or heating them up.. whats your advice?

Tre, the meet was fun. There were alot more trucks supposed to show that didnt end up showing..that kidna sucked. Also, I didnt get to clean my 01 AT ALL so it was dirty compared to everyone else's clean pix. My 01 is SO getting washed/clayed/waxed here sometime very soon. I cant wait to have some summer meets everyone!!

BTW all my pix will be posted soon. I decided to try something other than photosucket and ImageShack is slow. I want SmugMug but it's like 40.00 bucks or something and I dont need to spend that kind of dough right now

 

So you want to lower the rear of the 01? take the stock block out. I've had cranked bars for 4 years now...and progressively cranked more and more over the past couple of years. My truck has 83k on the clock and needs lower ball joints. Yes cranking the bars aiding in wearing the lowers, but them again, these lowers were stock circa 2001, w/ 83k on them.....just crank them bars man. btw....don't heat leafs.

 

What's wrong with heating leafs? Isnt it the same as heating coils? And if i ditch the block I think it'll drop the rear too much. I want to ditch the block but i cant unless i get lift leafs, and if i get lift leafs then i have to lift the front :(

 

great trucks, guys! and the ohio campground looked like a lot of fun.

 

LMAO..u dont no what to do fred.... fred if u want to help maybe this weekend i'll get my front a lil lower i think if i throw cold water on the coils after i heat them it will be alright right.. no need to take them out of the truck i think.. let the weight of the truck sink her down and spray that water on?????????? that should stop the sinking.. do i get them red hot of just warm em up a little????? i dont no ne thing about metal work

 

Actually Fred what you should try to do is find a set of lift blocks from a 2wd Edge. They had a 2" block instead of the 4x4's 2.5". It might be enough to get it level.

 

what bashing? all I said was that your an expert in metallurgy and to consult you. We were just going to go by the advice you gave out we were actually discussing it at the meet.

Fred is I knew you wanted to lower the back more we could of taken your leafs out cooked them over the fire some and and then run some water on them in the creek and bolted them back on. Thats what I have learned from the heating process and making it safe.

actually hes the one that gets banned because he has a bad attitude and doesnt know how to control his anger.

And if you havent noticed, there several members poking fun at him and are not at all serious about what they are asking or going to do about the heating subject. Its sarcasm....

 

^^I noticed the sarcasm. And I was just ucking around with that comment man. As I thought ya'll were ucking around as well.

 

Looks like a good turnout! Tickets and drama and nobdy is going to explain what happened? I get a little of this and that in every post but no story? It's ok I don't want to **** anybody off, I'm jsut curious on what went down.


BTW this is my 1000 post

 

pm sent to outdoorsman

 

Send me the PM too, I wanna know!

 

Saw something about burnouts? "Expression of speed" or "expression of power" ticket possibly?

 

all kinds of events went down

But I was not involved in any of the trouble

 

Thanks Josh! Some people on these boards get worked up over nothing, like HID's oops yeah I said it. Ok I'm done stirring the pot.

 

Nah... Mark just likes to bring up old **** that's already been dealt with... He can't let **** go. HID's is something totally different... Almost every HID thread ends up getting locked..

 

I didnt even bring it up at the meet

 

What's wrong with 2wd ? By the way , nice trucks ! Next time I will drive my truck down 'cause you need at least one ugly truck in the group Looks like a fun time.

 

nice edit mark.. lol.. i saw the stuff u put on there before.. hahaha.. didnt no i was a couple of those things... learn something new everyday.. but ya i might of broughten it up bc of the torch we had to light the fire with.. my truck was sitting around and the rear is slightly lower than the front so i thought about doing it for like .000001 seconds.. besides the fact.. drop it its done with.. this is a picture thread.. go to the blow off section if u want to come on the ohio meet pic thread and bash pple... it was just a joke that got brought up at the meet... and someone posted it on here.. bad idea for doing that but no need for more bull shi t.. so post something about the meet or dont do ne thing at all plz

 

It's not funny. There's no joke.

 

ok well we all laughed about it.. but seriously i said drop it.. make a thread in the blow off section.. be mature about it and dont post ne thing about it again on this thread plz

 

Alright. Cool trucks.