Ok, before I say anything else.
Prices are OBO, please if you don't like the price, don't badger me about it, if it doesn't sell, I might lower the price after a while. If you want to shoot me an offer, send me a PM with a reasonable offer. If I don't like you're offer, I MIGHT shoot you a counter offer, or politely tell you no.
Also, YOU pay shipping. A couple things I will not ship, but might meet depending on distance, and might charge a small fee.
Anyways, all of this stuff I pulled off my stock 2004 Ext Cab Ranger Edge 4.0L 4x4.
Here we go:j

Stock Headlights and Corners, will sell all together, or seperate the set of lights and the set of corners for now. Don't really want to sell individually just yet.
Headlights and Corners together : $65
Headlights alone (set) : $50
Amber Corners (set) : $20




Stock 2 bulb tail lights (set) : $40 - SOLD


Stock 3rd brake light (1 bulb) : $15 - SOLD


Stock Dome Light : $10 - SOLD


Stock Mud Flaps : $15 (Nothing wrong, just a little dirty, I will clean before shipping)


Next Item Up, I'd prefer not to ship, but I am willing to look into it, to price it, most likely will not be cheap.
Stock Ext Cab Running Boards... has all bolts except for front 2, couldn't get them off truck, but I will try again, I'm sure you can pick up cheap at any hardware store.
Asking $80 OBO. Need cleaned up, minimal surface rust, need a little TLC.


Front bracket w/o bolts

The little bit of rust on them


Next up, is plastic drop in factory bedliner (step-side, short-bed) with ford logo (Pick-up only on this, or will meet)
It's in great shape, been covered by a tonneau cover, very little scratches, nothing really deep.



Last up is my snap on tonneau cover (step-side, short-bed)
It's in great shape, I even have the original install instructions, all hardware, bracekets, bars, etc. Brand new cost almost $200... asking $110 OBO.






Trying to get some money back from all the mods I'm doing. I need a low profile step-side tool-box, a polished billet grille, if you have either, PM me, might be willing to deal a little. Also looking for a couple 06 ranger fender badges.
P.S. I am keep the rail caps for the bed, for now, but if you make me the right offer, I might be willing to part with them.
Thanks for looking, look forward to hearing from you.

 

Hows the hazing on your headlights? Any scratches?

 

I never noticed any hazing on them until I bough brand new ones and set em up next to it. So it's almost non-existent. I'm pretty sure there aren't any scratches, but I will look in the AM really close to verify. I wasn't planning on selling with any lamps, but I do have 2 brand new, never used, regular sylvannia 9007's that I could include for a small additional price, $15 maybe?

 

Updated... Tail lights, 3rd brake, and dome lights all sold.... very quickly I might add. Took out pictures so it's less to scan through.

 

Bump

 

Bumpity bump

 

bump

 

Bizzump

 

Bump again. Going to be posting this on Craigslist later on today. I would rather sell to someone on here, but I'm not getting any offers.

 

with that cover can you lift it up or on roll it or how does it work? cuz if im looknig at it right it looks like it will still have the bars going across you unsnap the cover and any installes pics??? and would you separate the tail gate cover too? thanks

 

It is just a button down, you can remove the middle support bars, and at the front of it, it has "strings", looks like web belt sorta, so you can roll it up, and tie it at the front. Let me run out and take a couple pics so this makes sense. And I'll get a good one up of it installed on the truck.
As far as the tailgate cover, I'm assuming you mean the plastic bed-liner part. For now, I'd like to keep it together, I would think it might sell easier that way. I wrote your username down and will keep you in mind if I do end up selling it seperate.

 

Here's more pics of the tonneau cover.
Pic of it installed

Pic of the tie down strings so you can roll it up

Last pic is showing how the bars can come out really easily so it can be rolled up

 

Bumpity Bump. I quoted another member shipping from CA to SC and it was close to $40 on the tonneau cover. It's wrapped up and ready to ship. If you're interested and closer, it will certainly be cheaper than that to ship, and I can ship immediately after payment. Still have mud flaps, head lights, corners, and the bed liner. REMINDER: This is for a STEPSIDE bed. :)

 

Dang, I wish that cover wasnt only for a step side, or I'd buy it. Sorry. Free BUMP!

 

Yea, my stepside is really starting to get on my nerves. Can't find a toolbox, can't sell my tonneau cover, rail caps have to stay on, and I can't get rid of my bed liner. Thanks for the bump tho. If anybody's interested in anything, PM me offers. I know someone needs some headlights to mod at the very least. Need to get rid of this stuff :)

 

See if there is a steppie group, and start a thread in there.

 

Still for sale, Need it gone, buy it. Thanks

 

Bump again. Still have this stuff. I know somebody's itching to get some stock stuff. Lol

 

Bump. Make offers.

 

u still have the headlights?

 

Yes, I do, boxed up, ready to be shipped. Be about $21 to ship to Charlotte. Just fyi.

 

Can you get me a quote on shipping to Edgeley Saskatchewan Canada ? it's probobaly high but maybe not oh i'm new here but as reference you can check out my feedback on ebay i'm paddd69 there
thanks
paddd

 

Hi,
Are these front or rear. ? with or without fender cutouts
tx=brian

 

These are rear flaps. Fender cut-outs? I'm guessing you mean for flares? I'm steppie, no flares. I can try to take better pics tomorrow and get em up if you like. Might even clean em for ya, cuz I'm a nice guy like that.

 

Ok, more and better pics of mud flaps, and cleaned up too.