tbar. how much is 2 much?
tbar. how much is 2 much?
Doing the shackle's this weekend. already cranked t-bar a 1" or so to level it out with the back. My question is how much more can i crank it before its TOO much? I've done research and found out that all lvl 2's have the #1 bars which is what i have. I understand about have the recoil and everything in the front just wasn't sure if someone on here has'em cranked up 2-2.5" or not. Thanks for the help and info!! I'll get pics up this weekend when it done of the before and after!!
I have my bars maxed but i have the B bars. i dont know how much of a difference in the amount you can raise between the 1s and the Bs. I would like to know the difference in how much more it can raise it with the 1 bars because i would just go to the jy and swap them.
May want to get an alignment if you go higher though just incase but some don't need it. i did mine just to prevent uneven wear but its up 2 u
May want to get an alignment if you go higher though just incase but some don't need it. i did mine just to prevent uneven wear but its up 2 u
Unregistered User
Posts: n/a
A brand new set of ' F ' rated bars will take more cranking on then an abused set of ' 1 ' bars. The elasticity of the bar itself is what matters most.
You might have #1 bars and the truck parked next to yours might have #1 bars as well. If yours or theirs has seen more severe use, the truck with the ' less abused ' bars will be able to take more tension and be more reliable.
Its all a mathematical calculation.
The amount of ' Lift ' your going to see from ANY of the bars will all be the same. You will be limited to the suspensions travel by means of hitting the bump stops for upper travel and stopping at the extent of angle on the upper balljoint. The bars themselves will only really control the reaction or speed of suspension correction.
I know the 08's sit and inch lower stock then 07-.
It doesn't matter what bars you have, its ' How good of condition are they in before I crank on them? '.
A brand new set of ' F ' rated bars will take more cranking on then an abused set of ' 1 ' bars. The elasticity of the bar itself is what matters most.
You might have #1 bars and the truck parked next to yours might have #1 bars as well. If yours or theirs has seen more severe use, the truck with the ' less abused ' bars will be able to take more tension and be more reliable.
Its all a mathematical calculation.
The amount of ' Lift ' your going to see from ANY of the bars will all be the same. You will be limited to the suspensions travel by means of hitting the bump stops for upper travel and stopping at the extent of angle on the upper balljoint. The bars themselves will only really control the reaction or speed of suspension correction.
A brand new set of ' F ' rated bars will take more cranking on then an abused set of ' 1 ' bars. The elasticity of the bar itself is what matters most.
You might have #1 bars and the truck parked next to yours might have #1 bars as well. If yours or theirs has seen more severe use, the truck with the ' less abused ' bars will be able to take more tension and be more reliable.
Its all a mathematical calculation.
The amount of ' Lift ' your going to see from ANY of the bars will all be the same. You will be limited to the suspensions travel by means of hitting the bump stops for upper travel and stopping at the extent of angle on the upper balljoint. The bars themselves will only really control the reaction or speed of suspension correction.
Unregistered User
Posts: n/a
I will repeat what I said before though. The PHYSICAL limitations are the bumpstops on the lower control arm, the upper balljoint on down travel, and the overall rigidity of the bars themselves.
If you wish to just crank them till they max out, its your truck. If everyone else has done it without problems, you shouldn't pay any mind that one might be beyond its limits, snap, and possibly cause a lot of damage. The statistics of the posters here shows people have ' cranked ' or ' maxed them out ' and haven't had any problems. Odds are you won't either by the laws of ' probability '.
Physics is what counts though.
Last edited by D.; Dec 20, 2008 at 02:31 PM.
Member
Joined: Aug 2007
Posts: 63
Likes: 0
From: WI
That's gotta be the biggest load of bull I've read tonight!! You know more about the front suspension on these trucks than 75% of us on here!
Unregistered User
Posts: n/a
When Inbred/Rednek-ism is addressed, maybe some of the more technical people will start posting on a regular basis again.
Until then, crank the bars, big tires, body lift, GIT R DUN!
Member
Joined: Oct 2008
Posts: 275
Likes: 0
From: Galway, NY
i like how ur thinkin D. I may be a redneck also but im sensible about my vehicles and crankin t-bars to the maxx is deffinately not a smart path to travel
I kinda agree. that's what Mike said today about maxin out the bars they really wear on the ball joints and tie rod ends. I Will get the shackles on and see where im at. I MIGHT just go ALMOST all the way but try my best to leave a lil play either way with it. we'll see what happens. Got my shackles in today so it will be sometime this week or this weekend. Santa is bringin a 3" PA BL for xmas and i just bought sea-bass's wheels. Have tires left to buy so i may just wait until i get everything together and put it all on at once. Will see. thanks D for the GREAT and more LOGICAL advice of it!! AND everyone else also!!
yeah I read somewhere they are 16mm lower than 2007.
My '02 B4000 with 31s and just the torsions cranked enough to level the truck out looks like a monster compared to my dad's 08 B4000 which is completely stock.
Member
Joined: Mar 2008
Posts: 1,332
Likes: 5
From: Canada
You told me in a PM that you own this Website.
Thread
Thread Starter
Forum
Replies
Last Post
