DOHC - 2.3L Duratec / Mazda L Engines Discussions and Topics specific to the Duratec 4 cylinder engines

Please Help, High idle

Thread Tools
 
Search this Thread
 
Old Aug 3, 2010
  #1  
JustinHammonds's Avatar
Thread Starter
|
Member
Joined: Aug 2010
Posts: 2
Likes: 0
From: martinez, ga
Please Help, High idle

okay, I have a 1999 regular cab 5 speed manual 2.5, and for some reason when im driving, ill goto push my clutch in and my motor wil start to rev up really high and doesnt stop until a few seconds after im at a complete stop, anyone have this problem or know what may be causing this, i would deeply appreciate it,

thanks for the help
 
Reply
Old Aug 4, 2010
  #2  
t5cents's Avatar
Member
iTrader: (6)
Joined: Nov 2008
Posts: 1,521
Likes: 1
From: Eureka, CA
IAC...search
 
Reply
Old Aug 4, 2010
  #3  
nofatchx's Avatar
Member
Joined: Aug 2010
Posts: 30
Likes: 0
From: DUM
its the throttle position sensor!!!!!!!!!! two phillips screws take it off dont get it from autozone id go dealer or elsewhere i had this problem also i did clean out the idle air motor with carb cleaner too ive known 5 people with this problem
 
Reply
Old Aug 4, 2010
  #4  
JustinHammonds's Avatar
Thread Starter
|
Member
Joined: Aug 2010
Posts: 2
Likes: 0
From: martinez, ga
THANKS YOU GUYSSS!!! ive been tryin to figure this out for agesssss, hopefully this works
 
Reply
Old Nov 17, 2010
  #5  
alanpeeples's Avatar
Member
Joined: Nov 2010
Posts: 5
Likes: 0
From: dora, al
did replacing the TPS work?
 
Reply
Old Nov 19, 2010
  #6  
Marchy's Avatar
Member
Joined: Dec 2009
Posts: 287
Likes: 0
From: Redmond, WA
Cleaning the IAC and replacing the TPS got this issue under control on my truck, my idle still hangs every once in a while (mostly when its very hot outside) so i think i'll eventually have to replace the IAC but it doesn't hurt the running of the motor. same year same motor same transmission.

edit: Also when you clean the IAC, replace the gasket that goes on there (1$ from napa) because when i first cleaned my IAC the issue did no go away and only once i replaced the gasket did it go away.
 
Reply
Old Nov 19, 2010
  #7  
alanpeeples's Avatar
Member
Joined: Nov 2010
Posts: 5
Likes: 0
From: dora, al
thank you. i have a new iac but not TPS,
 
Reply
Old Sep 8, 2012
  #8  
mnjsisk1's Avatar
Member
Joined: Sep 2012
Posts: 2
Likes: 0
From: WOODRUFF
I'm having this problem as well. I changed the IAC last year and it went a way for a good while. The problem is back. One variation from the poster. Mine does not idle back down once I get to a stop, it continues to run very high until I start going again and 1st gear forces it into a slower mode. It seems to want to go faster as well. Do I need another IAC or could it be something else?
 
Reply
Old Oct 3, 2012
  #9  
97ranger xlt's Avatar
Member
Joined: Feb 2007
Posts: 515
Likes: 9
From: PSL, FL
a bad pcv valve will cause a high idle and not throw a code.
 
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
thom2003
2.9L & 3.0L V6 Tech
3
Apr 5, 2020 04:00 PM
pacmanj4
General Ford Ranger Discussion
34
Jan 4, 2011 03:55 PM
4door
2.9L & 3.0L V6 Tech
7
Dec 16, 2010 11:49 AM
RickStar
SOHC - 2.3L & 2.5L Lima Engines
5
Sep 29, 2009 06:05 PM




All times are GMT -6. The time now is 05:23 PM.