4.0L OHV & SOHC V6 Tech General discussion of 4.0L OHV and SOHC V6 Ford Ranger engines.

code PO455 and it wont start - help

Thread Tools
 
Search this Thread
 
  #1  
Old 04-02-2010
GTXKen's Avatar
Member
Thread Starter
Join Date: Apr 2010
Location: Lowell
Posts: 7
Likes: 0
Received 0 Likes on 0 Posts
code PO455 and it wont start - help

New guy here with a new problem

The ranger won't start and the only code I pull is PO455, it says thats the evac system but I can't believe it. If I pour a little fuel in it it runs for a second or two, could it be the fuel pump?

Thanks in advance
Ken
 

Last edited by GTXKen; 04-02-2010 at 06:00 PM.
  #2  
Old 04-02-2010
Toreador4x4's Avatar
Member
iTrader: (6)
Join Date: Apr 2007
Location: Livonia, MI
Posts: 3,958
Likes: 0
Received 3 Likes on 3 Posts
smack the bottom of the gas tank a few (10-20) times with a hammer while cranking...see if it will start
 
  #3  
Old 04-02-2010
GTXKen's Avatar
Member
Thread Starter
Join Date: Apr 2010
Location: Lowell
Posts: 7
Likes: 0
Received 0 Likes on 0 Posts
Thanks, stick around and I'll try right now
 
  #4  
Old 04-02-2010
GTXKen's Avatar
Member
Thread Starter
Join Date: Apr 2010
Location: Lowell
Posts: 7
Likes: 0
Received 0 Likes on 0 Posts
Nothing, won't start. What do you think?
 
  #5  
Old 04-02-2010
Toreador4x4's Avatar
Member
iTrader: (6)
Join Date: Apr 2007
Location: Livonia, MI
Posts: 3,958
Likes: 0
Received 3 Likes on 3 Posts
when you turn the key to the "on" position, do you hear the fuel pump run for approx 2 seconds?
 
  #6  
Old 04-02-2010
GTXKen's Avatar
Member
Thread Starter
Join Date: Apr 2010
Location: Lowell
Posts: 7
Likes: 0
Received 0 Likes on 0 Posts
Not at all
 
  #7  
Old 04-02-2010
Toreador4x4's Avatar
Member
iTrader: (6)
Join Date: Apr 2007
Location: Livonia, MI
Posts: 3,958
Likes: 0
Received 3 Likes on 3 Posts
check fuel pump fuse and relay under the hood in the battery junction block (pretty sure there isnt a fuse inside the truck for it) and if the fuse is good (power on both sides of it with the key on) and the replay clicks (once when the key is turned on and once about 2 seconds later) the fuel pump is probably bad...replace the filter at the same time as the pump
 
  #8  
Old 04-02-2010
GTXKen's Avatar
Member
Thread Starter
Join Date: Apr 2010
Location: Lowell
Posts: 7
Likes: 0
Received 0 Likes on 0 Posts
Fuse is fine and the relay checked out, even swapped it with one we knew worked.
 
  #9  
Old 04-02-2010
GTXKen's Avatar
Member
Thread Starter
Join Date: Apr 2010
Location: Lowell
Posts: 7
Likes: 0
Received 0 Likes on 0 Posts
I would have guessed fuel pump but the code makes no mention of fuel pump as the cause, what gives?
 
  #10  
Old 04-02-2010
SB05EDGE's Avatar
Member
iTrader: (1)
Join Date: Nov 2007
Location: Midland, Texas
Posts: 534
Likes: 0
Received 0 Likes on 0 Posts
the code is the cause of something wrong with the EVAP system......fuel just happend to go out at the same time i guess.

i see that code all the time at my work
 
  #11  
Old 04-04-2010
Ranger093's Avatar
Member
iTrader: (1)
Join Date: Jul 2009
Location: Blaine, Minnesota
Posts: 289
Likes: 0
Received 0 Likes on 0 Posts
Go by the passenger kick panel in the cab by where a persons feet would rest. Look and see if you see a white cylinder shaped object. Press and hold it for 10 seconds with the key on then turn it off and do it again. Then try cranking the engine again and see if she fires up.
 
  #12  
Old 04-04-2010
--weezl--'s Avatar
Member
iTrader: (1)
Join Date: Sep 2009
Location: Calgary AB, Canada
Posts: 3,139
Likes: 0
Received 1 Like on 1 Post
Originally Posted by Ranger093
Go by the passenger kick panel in the cab by where a persons feet would rest. Look and see if you see a white cylinder shaped object. Press and hold it for 10 seconds with the key on then turn it off and do it again. Then try cranking the engine again and see if she fires up.
x2

fuel cutoff switch... there should even be a warning in the engine bay, forget what the part is called, right above the radiator
 
  #13  
Old 04-12-2010
GTXKen's Avatar
Member
Thread Starter
Join Date: Apr 2010
Location: Lowell
Posts: 7
Likes: 0
Received 0 Likes on 0 Posts
We bought a fuel pump the day after I posted. Looks like it was going to be a lot of work to drop the tank (3/4 take of fuel as well) so we pulled the bed instead, only took like 30 minutes. Dropped in the new pump and she fired right up.

Thanks Justin for being so quick to reply.

For the record the codes are BS and mentioned only the evac system!

Ken
 
  #14  
Old 04-12-2010
--weezl--'s Avatar
Member
iTrader: (1)
Join Date: Sep 2009
Location: Calgary AB, Canada
Posts: 3,139
Likes: 0
Received 1 Like on 1 Post
fuel pump wouldn't throw codes... otherwise you would throw those codes if you ever ran out of gas, and would have to pay someone to clear them every time...
 
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
lsf53
General Technical & Electrical
4
09-13-2012 03:51 PM
neville293
SOHC - 2.3L & 2.5L Lima Engines
2
06-30-2011 09:54 PM
Masteratarms93
General Ford Ranger Discussion
7
11-10-2010 05:05 PM
dantheman
General Technical & Electrical
4
08-26-2010 06:33 PM
skydivr7673
2.9L & 3.0L V6 Tech
11
02-11-2008 02:19 PM



Quick Reply: code PO455 and it wont start - help



All times are GMT -6. The time now is 10:36 PM.