At it again, yes always doing something.

Picked up a 1978 Ford Dana 60 High Pinion, kingpin front axle, along with its matching rear.



Ordered from www.4wdfactory.com

1 x Dana 60 USA Standard Gear, Reverse Rotation Ring & Pinions (Ratio: 5.13 Thick)
1 x Dana 60 Ring & Pinion Partial Install Kits (Front/Rear/Disconnect: Front, Pinion, Bearing or Shim kits: Minimal Shim Kits)
2 x Dana 60 King Pin Rebuild Kit
2 x Dana 60, Lower King Pin / Cap
2 x Dana 60 Kingpin ARP High Steer Stud Kits (Steering Arm Stud options: 4 Stud Kit)
1 x Dana 60 (some Dana 50), Spindle Nut Sockets, 4 point,OTC 7158
1 x Blue Torch Fab Dana 60 High Steer Arms (Style: Heim, Side: Full Kit - Both sides)
2 x Dana 60 / 50 Front Axle U-joint (Style: Non-Greasable)

Ordered from www.ballisticfabrication.com

1 - BRK-1008-1 Lower axle link brackets / Axle Tube Diameter: 3.0'' / Degree Offset: 0 degree Mounting Width / Hole size: 2.63 inch w/ 9/16 inch bolt
12 - SPA-553 303 SS Spacer 3/4 in.
2 - JAM-709 3/4" -16 tpi Jam Nut Thread Hand / Right Hand Thread
1 - RE-909 XM-12 3/4" CrMo rod end w/ kevlar liner / Thread Hand: Right Hand Thread
1 - RE-910 XM-12 3/4" CrMo rod end w/ kevlar liner / Thread Hand: Left Hand Thread
2 - JAM-710 3/4" -16 tpi Jam Nut / Thread Hand: Left Hand Thread
1 - TA-215 3/4" -16 tpi Tube Adapter / Tube Inner & Outer Diameters: Size 2: 1.0 in ID - 1.5 in OD / Thread Hand: Right Hand Thread
1 - TA-216 3/4" -16 tpi Tube Adapter / Tube Inner & Outer Diameters: Size 2: 1.0 in ID - 1.5 in OD / Thread Hand: Left Hand Thread
1 - TA-217 3/4" -16 tpi Tube Adapter / Tube Inner & Outer Diameters: Size 5: 1.25 in ID - 1.75 in OD / Thread Hand: Right Hand Thread
1 - TA-218 3/4" -16 tpi Tube Adapter / Tube Inner & Outer Diameters: Size 5: 1.25 in ID - 1.75 in OD / Thread Hand: Left Hand Thread
1 - BRK-1004-2 Link Tower / Separation from Axle center: 7 inches / Axle Diameter: 3.0 inches / Mounting Width / Bolt Hole: 2.63'' w/ 9/16'' hole
1 - BRK-1003-2 Panhard / Trackbar mount / Separation (from center of tube): 7 inches / Axle tube diameter: 3.0''
1 - BRK-1013-1 Dana 60 kingpin Coil over / Shock mounts/gussets / Axle: Ford
1 - BRK-1057-4 Axle tube shock tabs / Axle tube diameter: 3.0'' Plate thickness: 1/4''

 

hell yes! can't wait to see it done

 

small....

lol just joking I will be keeping an eye on it!

 

nice man cant wait!

 

Never satisfied huh Beard LOL... I can't wait to see...

 

Hey ECGS is like 10 min away from me, pretty cool. Looks good Zach!

 

Anybody buying your D44?

 

yeah its already sold along with that rear 60 i got.

 

Whats the difference between your current D60 and the new one?

 

Z, badass swap you have planned. sometimes, i wish i had a 4wd.....good luck and have fun!!!!

 

So when you outgrow this axle what one you gonna swap in next? lol

 

it in yet and broken yet? just wondering

 

Are they in and is the truck airborne yet?

 

About time. Why not a selectable locker this time around?

 

I was wondering the same thing, I think he just got it as a matching pair... Since he is sayin he sold it.. Would hope he's not rippin out a D60 to put in a D60

 

he is not swapping in the 60 he just bought, he just wanted the 60 front and the guy would only sell them as a set.

 

awesome man

 

That's what I'm talking about!!!

 

Haha awesome Zach! I love surprises. Wasn't it like 2 days ago that you said you might get a 60 in a few weeks!? LOL

 

after he's got the d60s set right
rockwells

http://www.redbarncustoms.net/

 

sexy lady flanges.

 

A set of portals would look sexy in there...... When you making it rear steer?

 

Hell yeah Zach Beef

 

good golly man, that's going to be awesome, before too long you'll have rockwells or something, lol, I like it man.

 

Awesome move Beard! I bet you could have saved some serious green if you would have started off with a D60 front axle. We live and learn....