General Ford Ranger Discussion General discussion of the Ford Ranger that does not fit in any other sub-forum.
Sponsored by:
Sponsored by: DashLynx

Will not heat up correctly

Thread Tools
 
Search this Thread
 
  #1  
Old 12-16-2007
Advocate's Avatar
Member
Thread Starter
Join Date: Jun 2006
Location: Corvallis, OR
Posts: 35
Likes: 0
Received 0 Likes on 0 Posts
Will not heat up correctly

so here is the new problem.

Just replaced the head gaskets, Thermostat and heater control vale.


The truck is no longer over heating, but now it wont heat up correctly. It heats up to the appropriate level while it is idling, then about a min later it drops to just about cold. While running down the road it is running it runs colder than it should also. So Im wondering what could be causing this. Keep in mind it has a brand new thermostat. oh and yes I got the heads milled and replaced both head gaskets.
 
  #2  
Old 12-17-2007
wydopnthrtl's Avatar
Member
iTrader: (2)
Join Date: Dec 2005
Location: Ohio
Posts: 2,496
Likes: 0
Received 8 Likes on 6 Posts
The only thing that would allow for over cooling is the stat.

Rich
 
  #3  
Old 12-17-2007
Join Date: Aug 2006
Location: Demorest,Ga
Posts: 1,724
Likes: 0
Received 0 Likes on 0 Posts
mine does the same thing...even in the summer, the only time it would even get near mid way on the temp gauge was if you let it idle a bit...in the winter, i dont think it even gets above the cold mark.
 
  #4  
Old 12-17-2007
Advocate's Avatar
Member
Thread Starter
Join Date: Jun 2006
Location: Corvallis, OR
Posts: 35
Likes: 0
Received 0 Likes on 0 Posts
yea that is wierd, basically the same as what mine is doing... not very much heat out of the heater either.

ITS NOT THE THERMOSTAT lol

replaced the thermostat, temp sensor, heater valve, head gaskets, Flushed the system a couple times. fan clutch prolly has 15k miles on it.

anyone got any ideas???
 
  #5  
Old 12-18-2007
Ranger Carl's Avatar
Member
Join Date: Dec 2007
Location: Taylorsville Ky
Posts: 293
Likes: 0
Received 2 Likes on 2 Posts
Are you sure you installed the thermostat correctly??

I have bought several bad thermostats in sucession.

Try removing the thermostat and putting it in a soup can of water and held off the sides and bottom of the can with wires. Use a good bulb thermometer or such that will go past boiling, at least to 300deg.F. Take a torch and heat the water and when the temp shows what the thermostat is rated at it should start opening. If sooner or later the thermostat is bad. Replace it.

edit: yeah, you can use the stove but I am shop oriented and seldom think house. I guess it's all the years in trk shops and machine shops.
 

Last edited by Ranger Carl; 12-20-2007 at 09:51 AM.
  #6  
Old 12-18-2007
Overkill-F1's Avatar
Member
Join Date: Aug 2007
Location: Powell River,BC, Canada
Posts: 56
Likes: 0
Received 0 Likes on 0 Posts
I second the idea of testing the new thermostat. It could stick open. I would use the kitchen stove instead, for better control.
...Terry
 

Last edited by Overkill-F1; 12-18-2007 at 08:17 PM.
  #7  
Old 12-19-2007
Advocate's Avatar
Member
Thread Starter
Join Date: Jun 2006
Location: Corvallis, OR
Posts: 35
Likes: 0
Received 0 Likes on 0 Posts
hmm thats a good idea for testing it. yea I figured beacuse i blew the head gasket from overheating it might had killed the brand new thermostat i put in so i replaced it with another new one from a different store of a different brand. typically when you have several bad ones in a row its because the batch produced was bad. I might give that test a shot.
 
  #8  
Old 12-26-2007
rangerxlt4x4's Avatar
Member
Join Date: Jun 2007
Location: ohio
Posts: 90
Likes: 0
Received 0 Likes on 0 Posts
the themostat most likely needs replaced you said it doesn't over heat now and cools down when u drive it must be opening to early and is stuck open.
 
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
overtheedge1
Drivetrain Tech
2
01-16-2015 06:07 PM
BLCNBLU
Drivetrain Tech
0
02-10-2013 07:59 PM
Saberball
General Technical & Electrical
0
06-15-2011 06:16 PM



Quick Reply: Will not heat up correctly



All times are GMT -6. The time now is 02:13 PM.