Dana60 Swap...
#27
#28
meh i had a good time with the 44, learned a ton, so i dont regret it, dont really care about the green so called wasted.
thanks for the comments guys.
the guy sold them as a pair, so i just bought it, i am sure i will find a use for that rear 60, or i will just keep it for parts.
I stripped the whole thing down, never seen an axle from this time frame look so good. the internals are mint, and everything is in great shape. I already had rotors that worked from an incorrect purchase for the 44. All I really need is the kingpin rebuild stuff, wheel bearing seals, and some new grease. the bearings are in great shape too. Same with the u-joints.
The lockouts were broken, so I need some type of replacement, probably just drive flanges.
thanks for the comments guys.
the guy sold them as a pair, so i just bought it, i am sure i will find a use for that rear 60, or i will just keep it for parts.
I stripped the whole thing down, never seen an axle from this time frame look so good. the internals are mint, and everything is in great shape. I already had rotors that worked from an incorrect purchase for the 44. All I really need is the kingpin rebuild stuff, wheel bearing seals, and some new grease. the bearings are in great shape too. Same with the u-joints.
The lockouts were broken, so I need some type of replacement, probably just drive flanges.
#30
#31
#33
#34
#36
this should get me going...
Your Order Contains the Following Items:
1 x Dana 60 USA Standard Gear, Reverse Rotation Ring & Pinions (Ratio: 5.13 Thick)
1 x Dana 60 Ring & Pinion Partial Install Kits (Front/Rear/Disconnect: Front, Pinion, Bearing or Shim kits: Minimal Shim Kits)
2 x Dana 60 King Pin Rebuild Kit
2 x Dana 60, Lower King Pin / Cap
2 x Dana 60 Kingpin ARP High Steer Stud Kits (Steering Arm Stud options: 4 Stud Kit)
1 x Dana 60 (some Dana 50), Spindle Nut Sockets, 4 point,OTC 7158
1 x Blue Torch Fab Dana 60 High Steer Arms (Style: Heim, Side: Full Kit - Both sides)
2 x Dana 60 / 50 Front Axle U-joint (Style: Non-Greasable)
Your Order Contains the Following Items:
1 x Dana 60 USA Standard Gear, Reverse Rotation Ring & Pinions (Ratio: 5.13 Thick)
1 x Dana 60 Ring & Pinion Partial Install Kits (Front/Rear/Disconnect: Front, Pinion, Bearing or Shim kits: Minimal Shim Kits)
2 x Dana 60 King Pin Rebuild Kit
2 x Dana 60, Lower King Pin / Cap
2 x Dana 60 Kingpin ARP High Steer Stud Kits (Steering Arm Stud options: 4 Stud Kit)
1 x Dana 60 (some Dana 50), Spindle Nut Sockets, 4 point,OTC 7158
1 x Blue Torch Fab Dana 60 High Steer Arms (Style: Heim, Side: Full Kit - Both sides)
2 x Dana 60 / 50 Front Axle U-joint (Style: Non-Greasable)
#37
I just need to buy 4 brackets from Ballistic. Lowers, Upper link mount, and panhard mount.
then some drive flanges. Not too bad. Should be able to get the axle under there for about 1500, plus the 800 for the axle.
idk what i want for a locker, might just hold out for a detroit later and run an open diff. though I hate open diffs. lol
then some drive flanges. Not too bad. Should be able to get the axle under there for about 1500, plus the 800 for the axle.
idk what i want for a locker, might just hold out for a detroit later and run an open diff. though I hate open diffs. lol
#39
I would run it open then get a detroit. thats just me though.
#40
found this place online selling all Dana Spicer stuff for the kingpin, plus they had yukon gears 20$ cheaper than anywhere i had seen.
4WD Factory
I have never heard of them until the other day (ranger) posted something about his Dana60 build, they sell ruffstuffspecialties.com, ballisticfabrication.com, bluetorchfab.com and trailgear.com parts, brackets, etc....
so they must be decent??
4WD Factory
I have never heard of them until the other day (ranger) posted something about his Dana60 build, they sell ruffstuffspecialties.com, ballisticfabrication.com, bluetorchfab.com and trailgear.com parts, brackets, etc....
so they must be decent??
#43
i have a ton of lockouts, balljoints, hubs, brakes, etc...
#49