Drivetrain Tech General discussion of drivetrain for the Ford Ranger.

Avm Manual Hub Install Help!!!

  #1  
Old 03-22-2008
huggyjd's Avatar
Member
Thread Starter
Join Date: Feb 2008
Location: AUBURNDALE,FL
Posts: 8
Likes: 0
Received 0 Likes on 0 Posts
Avm Manual Hub Install Help!!!

Well I Installed 1 Of My Avm Locking Hubs On My 98 Ranger Without A Glitch! Took 15 Minutes. When I Got To The Other Wheel, The Old Hub Was Froze Up With Rust And Dirt. I Tried To Pry It Loose And All That Happened Is The Whole Plasic Shell That Sticks Out Broke Off Flush Leaving All The Gears And Guts Intact Around The Spine. Now How Do I Get The Rest Of The Old Hub Out? Thanks
 
  #2  
Old 03-22-2008
chris_w_2008's Avatar
Member
Join Date: Sep 2007
Location: michigan
Posts: 157
Likes: 0
Received 0 Likes on 0 Posts
spray some lub or something on it i actually preped my hubs before putting in maunual i had to beat on my a little to get it to break loose i just did mine wed and my passenger side was stuck but tues night i preped them
 
  #3  
Old 03-22-2008
huggyjd's Avatar
Member
Thread Starter
Join Date: Feb 2008
Location: AUBURNDALE,FL
Posts: 8
Likes: 0
Received 0 Likes on 0 Posts
hubs

The problem is , I have nothing to grab hold of to get the rest of the hub guts out.
 
  #4  
Old 03-22-2008
MudSlanger's Avatar
Member
iTrader: (4)
Join Date: Jun 2007
Location: Phoenix, AZ
Posts: 1,462
Likes: 0
Received 0 Likes on 0 Posts
take a rubber mallet to it and tap it. tapping it will loosen up some of the rust and dirt. vise grips maybe and pull it out? use some sort of prying device. improvise alittle with the tools u have.
 
  #5  
Old 03-22-2008
chris_w_2008's Avatar
Member
Join Date: Sep 2007
Location: michigan
Posts: 157
Likes: 0
Received 0 Likes on 0 Posts
give her a good smack!!! if the hub was to be locked could that be the problem?
 
  #6  
Old 03-22-2008
huggyjd's Avatar
Member
Thread Starter
Join Date: Feb 2008
Location: AUBURNDALE,FL
Posts: 8
Likes: 0
Received 0 Likes on 0 Posts
re

There is nothing to grab hold of. Its flush with the spline. The only possible solution I can think of is to drill a tiny hole in the hub gears and maybe get a aluminum screw started and use that to pull the rest of the hub guts out. maybe that will work. Its really caked up in there. Rust on the spline and on the hub guts. Its just froze up in there. when I pulled on the old hub, that whole black plastic part just broke off leaving the hub gears ect intact, flush with the spline.
 
  #7  
Old 03-22-2008
chris_w_2008's Avatar
Member
Join Date: Sep 2007
Location: michigan
Posts: 157
Likes: 0
Received 0 Likes on 0 Posts
my last choice would be a air hammer then i would start drilling and cutting away sorry to hear its being a pain for ya
 
  #8  
Old 03-22-2008
frdrangr369's Avatar
Member
Join Date: Jan 2008
Location: clymer, pa
Posts: 100
Likes: 0
Received 0 Likes on 0 Posts
where did u get ur hubs and wut kind are they? i ask this cause i want to convert to lockl hubs on my 99 but i cant find anybody that carries them for my truck. as for ur problem, id say the same, give her an ol smack.
 
  #9  
Old 03-22-2008
Rooks's Avatar
Member
iTrader: (7)
Join Date: Sep 2006
Location: Minneapolis, MN
Posts: 1,867
Likes: 0
Received 0 Likes on 0 Posts
Tellico4x4 is who sells AVM hubs.

As for what's happening, I'm don't understand what happened so I would say take a picture if you can. Might help clear up my screwed up head.
 
  #10  
Old 03-22-2008
huggyjd's Avatar
Member
Thread Starter
Join Date: Feb 2008
Location: AUBURNDALE,FL
Posts: 8
Likes: 0
Received 0 Likes on 0 Posts
re

Can i post a picture on here?
 
  #11  
Old 03-22-2008
99ranger4x4's Avatar
RF Veteran
iTrader: (3)
Join Date: Jun 2006
Location: Austin, TX
Posts: 12,198
Likes: 0
Received 3 Likes on 3 Posts
uhhhh

yea
 
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
chester burnett
Drivetrain Tech
0
02-03-2014 09:50 AM
cheese_man
Drivetrain Tech
2
10-01-2010 08:29 AM
Biz
Engine & Drivetrain
28
12-20-2008 10:51 PM


Thread Tools
Search this Thread
Quick Reply: Avm Manual Hub Install Help!!!



All times are GMT -6. The time now is 12:45 AM.