How do you replace CV's?
#1
11-09-2004
#2
11-09-2004
#3
11-09-2004
#4
11-09-2004
Join Date: Jun 2004
Location: Albuquerque, NM
Posts: 301
Likes: 0
Received 0 Likes
on
0 Posts
Did a search on
http://www.explorerforum.com/forums/
Search for no-slip locker or locker. There is a how to on removing the axle.
But heres a short one, the way I removed my cv-axles. Its not hard, just takes some time.
1. Block truck and jack up front and put on jack stands.
2. Remove wheels.
3. Remove axle nut. It is big, 27mm or something like that. Use impact or big cheater bar. If you use the cheater bar have someone step on the brakes to keep the axle from turning.
4.Use rubber hammer to tap axle out.
5.Remove bolt holding upper ball jonit and hit upper a-arm with hammer to get ball joint out.
6. Now u should be able to slide the cv axle out of the bearing (If replacing the pass. side might have to turn the wheel all the way to the left)
7. Now that u have that side out, use a pry bar or large screwdriver and pop the other side of the cv-axle off the axle. MAKE sure not to hit the rubber seal.
That should do it. Take you time and than just reverese the order.
Heres what the pass. side looks like after I took my out. Also I took the cailper off, do that b4 you remove the upper a-arm.
Good luck.
http://www.explorerforum.com/forums/
Search for no-slip locker or locker. There is a how to on removing the axle.
But heres a short one, the way I removed my cv-axles. Its not hard, just takes some time.
1. Block truck and jack up front and put on jack stands.
2. Remove wheels.
3. Remove axle nut. It is big, 27mm or something like that. Use impact or big cheater bar. If you use the cheater bar have someone step on the brakes to keep the axle from turning.
4.Use rubber hammer to tap axle out.
5.Remove bolt holding upper ball jonit and hit upper a-arm with hammer to get ball joint out.
6. Now u should be able to slide the cv axle out of the bearing (If replacing the pass. side might have to turn the wheel all the way to the left)
7. Now that u have that side out, use a pry bar or large screwdriver and pop the other side of the cv-axle off the axle. MAKE sure not to hit the rubber seal.
That should do it. Take you time and than just reverese the order.
Heres what the pass. side looks like after I took my out. Also I took the cailper off, do that b4 you remove the upper a-arm.
Good luck.
#5
11-09-2004
#6
11-09-2004
#7
11-09-2004
#8
11-10-2004
Join Date: Jun 2004
Location: Albuquerque, NM
Posts: 301
Likes: 0
Received 0 Likes
on
0 Posts
I Fixed The Site Clock... Adjust Yours Accordingly...
Oh for the PVH, I don't know how that works. I think u have to open up the hub than get the snap ring out and some small allen key bolts. But thats just a guess.
Heres the link I was talking about.
http://www.explorerforum.com/forums/...threadid=53863
Its to remove the axle.
Maybe check the rangerstation???
Heres the link I was talking about.
http://www.explorerforum.com/forums/...threadid=53863
Its to remove the axle.
Maybe check the rangerstation???
Thread
Thread Starter
Forum
Replies
Last Post
Red_Ak_Ranger
General Ford Ranger Discussion
20
08-29-2012 01:19 PM
fordman26
Drivetrain Tech
3
01-05-2011 05:26 AM
