Ebay Headlights.
#26
Originally Posted by SniperSmurf
on our trucks it's not a turn signal, not unless you do the mod. Trucks witrh the newer design have corner just as markers. I need to get around to doing that mod. Not that hard, but yet the how-to on gen-edge/rps makes it seem more difficult than it needs to be.
#27
ok. here it is in 10 easy steps.
1. preheat the oven to 250.
2. put each headlight in with the lense up on a cookie sheet for 14-15 minutes.
3. take out and start prying it open with a screwdriver.
4. put corner lenses in with the lense up on a cookie sheet for 7 minutes.
5. take out and start prying it open with a screwdriver.
6. tape off what you dont want to be painted.
7. paint.
8. reassemble with silicon sealer, clear or black.
9. put finished product back on the truck
10. stand back and enjoy cuz its over and it looks good.
1. preheat the oven to 250.
2. put each headlight in with the lense up on a cookie sheet for 14-15 minutes.
3. take out and start prying it open with a screwdriver.
4. put corner lenses in with the lense up on a cookie sheet for 7 minutes.
5. take out and start prying it open with a screwdriver.
6. tape off what you dont want to be painted.
7. paint.
8. reassemble with silicon sealer, clear or black.
9. put finished product back on the truck
10. stand back and enjoy cuz its over and it looks good.
#28
Originally Posted by RangerBoy03FX4
ok. here it is in 10 easy steps.
1. preheat the oven to 250.
2. put each headlight in with the lense up on a cookie sheet for 14-15 minutes.
3. take out and start prying it open with a screwdriver.
4. put corner lenses in with the lense up on a cookie sheet for 7 minutes.
5. take out and start prying it open with a screwdriver.
6. tape off what you dont want to be painted.
7. paint.
8. reassemble with silicon sealer, clear or black.
9. put finished product back on the truck
10. stand back and enjoy cuz its over and it looks good.
1. preheat the oven to 250.
2. put each headlight in with the lense up on a cookie sheet for 14-15 minutes.
3. take out and start prying it open with a screwdriver.
4. put corner lenses in with the lense up on a cookie sheet for 7 minutes.
5. take out and start prying it open with a screwdriver.
6. tape off what you dont want to be painted.
7. paint.
8. reassemble with silicon sealer, clear or black.
9. put finished product back on the truck
10. stand back and enjoy cuz its over and it looks good.
I think they are talking about the turn signal mod.
So that means they dont sell the clears at all anymore?
#30
alternating turnsignal mod.
1. pull healight out and access bulb wires
2. cut ground of corner bulb.
3. but connect a wire to the ground.
4. scotch lock that wire into the turn signal wire. (green/white for the driver side|white/green for the passenger side)
5. check to make sure it works.
6. reassemble.
1. pull healight out and access bulb wires
2. cut ground of corner bulb.
3. but connect a wire to the ground.
4. scotch lock that wire into the turn signal wire. (green/white for the driver side|white/green for the passenger side)
5. check to make sure it works.
6. reassemble.
#31
#32
#34
#35
#36
Thread
Thread Starter
Forum
Replies
Last Post
Dweano
OLD - Interior, Exterior, Electrical, & Misc.
0
04-28-2011 07:26 PM
btm757
Exterior Semi-Tech
29
11-23-2010 05:43 PM
Rolldogg
General Ford Ranger Discussion
13
03-03-2009 09:38 AM