installing aal's
#1
installing aal's
just now ordered them from summit. these are the ones
Pro Comp 13120 - Pro Comp Add-A-Leaf Kits
i know this should be really easy but, they will get here wednesday, and have to be somewhere at 530 and can start at 3 when i get home. i just want as much knowledge going into this as i can get before hand. you know, just to make sure i am okay and no unexpected delay's. so if someone can kinda walk me through it, or any helpful hints would be great. thanks!
EDIT: DONE
read last post for info.
oh, and yes i know i still need to trim the excess bolt off.
Pro Comp 13120 - Pro Comp Add-A-Leaf Kits
i know this should be really easy but, they will get here wednesday, and have to be somewhere at 530 and can start at 3 when i get home. i just want as much knowledge going into this as i can get before hand. you know, just to make sure i am okay and no unexpected delay's. so if someone can kinda walk me through it, or any helpful hints would be great. thanks!
EDIT: DONE
read last post for info.
oh, and yes i know i still need to trim the excess bolt off.
Last edited by yellow_edge; 05-19-2009 at 08:29 PM.
#3
#4
haha. sounds good. but im probably not gunna take the leafs completely off. heres my idea, correct me if im wrong...
jack up so tires are off
remove tires, u bolts and plate
clamp pack
remove pin
un clamp a little ?
put new **** in.
somewhat right? i know the old pin will be a ***** to get out.
oh and judging by summit, they will probably be here tuesday.
jack up so tires are off
remove tires, u bolts and plate
clamp pack
remove pin
un clamp a little ?
put new **** in.
somewhat right? i know the old pin will be a ***** to get out.
oh and judging by summit, they will probably be here tuesday.
#5
its a pretty straight forward project. remove leafs, take pic, dissassemble, take pic, use long bolt to tighten spring pack back together,take pic, reinstall leafs, take pic, jump for joy, take pic, finish beer, take pic, make hot girl pose in front of truck, take pic, post thread!
#9
#10
I did one side taking the leafs off the rear shackle and then realized there was no reason too and did the other side with the main leaf bolted in and just clamped the pack and then loosened them after cutting the head off the center pin. I put the new AAL in and started C-clamping back down while tightening the new center pin down as I went. I would wait for a Saturday if possible, daylight will cut down on your curse word count as you go.
Edit: There is no undoing the old center pin with a wrench afik, my truck is a 2006 and it was siezed and had a round head. Make sure and have or borrow and angle grinder with a cutoff wheel, or at the least a dremel and a lot of discs. All your other steps look good.
Edit: There is no undoing the old center pin with a wrench afik, my truck is a 2006 and it was siezed and had a round head. Make sure and have or borrow and angle grinder with a cutoff wheel, or at the least a dremel and a lot of discs. All your other steps look good.
Last edited by old greg; 05-19-2009 at 03:40 PM.
#11
okay. done. i will admit, it was a *****.
i left the leafs on, which is doable, but pretty hard to line everything up.
we had to cut the round end of the old centerpin to fit a wrench.
then just cut the nut off and pounded it through.
But, yes, aligning everything was really hard. I did that part alone, i was sitting on the floor, stradling the axle, yanking on it to they and get it to seed in with the factory block. With my other hand on the jack ready to release it lol.
Pics in a few minutes, there are like 5 or 6.
i left the leafs on, which is doable, but pretty hard to line everything up.
we had to cut the round end of the old centerpin to fit a wrench.
then just cut the nut off and pounded it through.
But, yes, aligning everything was really hard. I did that part alone, i was sitting on the floor, stradling the axle, yanking on it to they and get it to seed in with the factory block. With my other hand on the jack ready to release it lol.
Pics in a few minutes, there are like 5 or 6.
Thread
Thread Starter
Forum
Replies
Last Post