conversion
#1
#2
RF Veteran
iTrader: (1)
Yes you would need intake and a standalone carb(not feedback carb) for a 2.3l
Feedback carbs used a computer, and I assume you want to avoid this.
And you would need a duraspark distributor(vacuum advance) for 2.3l and HEI module(cheap), duraspark modules tended to fail.
Very easy wiring, have a look: How To Convert A Ford Or Chrysler Ignition To GM HEI - Car Craft
I think the Mustangs with 2.3l Lima engines used Duarspark distributors from '76 until the mid-'80's, Rangers only got the TFI system, which needs a computer for spark advance/retard, duraspark used vacuum advance/retard
Feedback carbs used a computer, and I assume you want to avoid this.
And you would need a duraspark distributor(vacuum advance) for 2.3l and HEI module(cheap), duraspark modules tended to fail.
Very easy wiring, have a look: How To Convert A Ford Or Chrysler Ignition To GM HEI - Car Craft
I think the Mustangs with 2.3l Lima engines used Duarspark distributors from '76 until the mid-'80's, Rangers only got the TFI system, which needs a computer for spark advance/retard, duraspark used vacuum advance/retard
Last edited by RonD; 02-01-2016 at 10:08 AM.
#3
esslinger cast iron 2 barrel intake manifold
2.3 Cast Iron Head Holley Manifold - store.esslingeracing.com
here are several videos to help you
https://www.youtube.com/results?search_query=ford+2.3
2.3 Cast Iron Head Holley Manifold - store.esslingeracing.com
here are several videos to help you
https://www.youtube.com/results?search_query=ford+2.3
Last edited by cheese_man; 02-01-2016 at 04:05 PM. Reason: readded link disappeared??
#4
RF Veteran
iTrader: (1)
Oh, and I forgot about the fuel pump.
Your current system has 30psi for the EFI, you need 5-9psi for the carb.
I think the '88 Rangers still have the 2 pump system, lift pump in tank and high pressure pump in the frame rail.
So you can remove the high pressure pump, need to connect the two hoses together.
Lift pump should supply enough fuel pressure.
Return fuel line won't be used.
The computer is what turns the fuel pump on and off, so with out it you will have to use another method.
Electric fuel pumps can be dangerous, if you are in an accident or roll over they can keep pumping fuel out of broken lines.
Your Ranger does have an inertia switch, which should cut power to the fuel pump in an accident or roll over, but...............it is your life.
What was done with electric fuel pumps and carbs was to use the oil pressure switch to turn on and off the Fuel pump power.
When you have oil pressure pump comes on, when no oil pressure pump goes off.
'88 with have an oil pressure switch, so it is on or off, not like a sender that shows when pressure goes up and down.
The switch is a ground for the gauge, when there is oil pressure switch closes and grounds the gauge, it's needle goes up to 1/4 or so and stays there.
The fuel pump relay powers the fuel pump, normally the computer grounds this relay when engine starts, so simple wiring to get oil pressure switch to do the same thing.
You need a diode on the new wire so the power doesn't flow back to dash board gauge.
Your current system has 30psi for the EFI, you need 5-9psi for the carb.
I think the '88 Rangers still have the 2 pump system, lift pump in tank and high pressure pump in the frame rail.
So you can remove the high pressure pump, need to connect the two hoses together.
Lift pump should supply enough fuel pressure.
Return fuel line won't be used.
The computer is what turns the fuel pump on and off, so with out it you will have to use another method.
Electric fuel pumps can be dangerous, if you are in an accident or roll over they can keep pumping fuel out of broken lines.
Your Ranger does have an inertia switch, which should cut power to the fuel pump in an accident or roll over, but...............it is your life.
What was done with electric fuel pumps and carbs was to use the oil pressure switch to turn on and off the Fuel pump power.
When you have oil pressure pump comes on, when no oil pressure pump goes off.
'88 with have an oil pressure switch, so it is on or off, not like a sender that shows when pressure goes up and down.
The switch is a ground for the gauge, when there is oil pressure switch closes and grounds the gauge, it's needle goes up to 1/4 or so and stays there.
The fuel pump relay powers the fuel pump, normally the computer grounds this relay when engine starts, so simple wiring to get oil pressure switch to do the same thing.
You need a diode on the new wire so the power doesn't flow back to dash board gauge.
Last edited by RonD; 02-02-2016 at 02:01 PM.
Thread
Thread Starter
Forum
Replies
Last Post
aford89
Wheels & Tires Semi-Tech
17
03-29-2009 01:09 AM
PickupMan92
General Ford Ranger Discussion
1
08-05-2004 02:27 PM